Additional Safety Rules For Charger & Battery Cartridge - Makita 4331D Manual De Instrucciones

ENGLISH
1 Button
2 Battery cartridge
3 Charging light
4 Battery charger
5 Loosen
6 Hex wrench
7 Bolt
8 Jig saw blade
9 Roller
10 The end of the blade shank
should reach the bottom of the
inner slit.
SPECIFICATIONS
Model
Length of stroke ........................................................................... 26 mm
Max. cutting capacities
Wood ........................................................................................ 65 mm
Mild steel .................................................................................. 10 mm
Aluminum .................................................................................. 20 mm
Strokes per minute ...................................................................... 500 – 2,800
Overall length .............................................................................. 280 mm
Net weight .................................................................................... 2.6 kg
Rated voltage .............................................................................. D.C. 12 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating instruc-
tions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
3. CAUTION — To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types
of batteries may burst causing personal injury
and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to per-
sons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
Explanation of general view
11 Lever
12 Speed adjusting dial
13 Lock-off button
14 Switch trigger
15 Base
16 Cutting line
17 Bolt
18 Cross-shaped slot
19 Edge of motor housing
20 Graduations
21 Starting hole
22 Anti-splintering device
8.
9.
10. Do not disassemble charger or battery cartridge;
11. To reduce risk of electric shock, unplug charger
ENC001-2
12. The battery charger is not intended for use by
13. Young children should be supervised to ensure
ADDITIONAL SAFETY RULES FOR
CHARGER & BATTERY CARTRIDGE
1.
2.
3.
4.
23 Plastic base plate
24 Guide rule
25 Threaded knob
26 Circular guide
27 Pin
28 Fit into notches.
29 Plastic cover
30 Nozzle
31 Limit mark
32 Screwdriver
33 Brush holder cap
4331D
Do not operate charger with damaged cord or
plug — replace them immediately.
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
take it to a qualified serviceman when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
young children or infirm persons without super-
vision.
that they do not play with the battery charger.
Do not charge battery cartridge when tempera-
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
Do not allow anything to cover or clog the
charger vents.
Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
4333D
26 mm
65 mm
10 mm
20 mm
500 – 2,600
280 mm
2.9 kg
D.C. 14.4 V
5