PowPak
|
Installation
Dimming Module with 0 –10 V
Part of the Vive Family
220 – 240 V~ 50 / 60 Hz 8 A
RMKS-8T-DV-B
0 –10 V Control: 10 V- 60 mA
Compatible with IEC 60929 Annex E
Note for Replacement:
RMxS - the "S" model can replace the non-"S" model
Important Notes: Please read before installing.
For installation by a qualified electrician in accordance with all local and
national electrical codes.
• Note: Use copper conductors only.
• Check to see that the device type and rating is suitable for the application.
• DO NOT install if product has any visible damage.
• If moisture or condensation is evident, allow the product to dry completely
before installation.
• Operate between 0 °C and 40 °C ambient.
• 0% to 90% humidity, non-condensing.
• For indoor use only.
PowPak
Dimming Module
Install in center of room to
maximize RF coverage.
Radio Powr Savr
Occupancy
Sensor
PowPak
9 m max
Dimming
Module
Pico
Remote
Control
12 m
All Wireless Transmitters must be installed within 9 m
of the PowPak Dimming Module with 0 –10 V.
Default Functionality
Occupancy Sensors
Occupied: All lights 100%.
Unoccupied: All lights off.
Daylight Sensor
All lights dim in response to daylight.
Link
Cal.
Test
Wireless Controls
On
All lights 100%
Favorite All lights 50%
Off
All lights off
Lutron EA Ltd | 125 Finsbury Pavement, 4th floor
London EC2A 1NQ, UK
Required Components
For each system, ensure that you have:
One PowPak Dimming Module
At least one Wireless Transmitter
041588
041644
Rev. A
Rev. A
12/2018
12/2018
Load Status LED
Raise
+
Toggle
Lower
Radio Powr Savr Occupancy/Vacancy Sensor
PowPak Dimming Module with 0 –10 V
(10 maximum)
(1 maximum)
Start Here
Mount, Wire, and Install 0 –10 V Devices
1
and Lighting Fixtures
Consult third-party device installation guide
WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit
breaker before installing the unit.
A Connect mains wiring (switched hot, neutral) to each fixture.
B Connect 0 –10 V control (+ and – ) to each fixture.
Green/Yellow
Fixture Earth
Neutral
Switched Line/Hot
+
Violet
–
Gray
To additional 0 –10 V fixtures
Programming with a Vive Hub
3
A
Use and iOS or Android compatible device.
B
Vive
X
Troubleshooting
Ballasts cannot be controlled locally from PowPak Dimming
Module with 0 –10 V.
Lights do not dim as expected.
Lights do not respond to Wireless Transmitter(s).
Lights are unstable at low-end or flash/flicker at turn-on or turn-off. • Adjust the low-end trim.
Wireless Transmitter(s) cannot be associated to PowPak
Dimming Module with 0 –10 V.
Pico Remote Control
(10 maximum)
Install PowPak Dimming Module
2
with 0 –10 V
Suggested Installation Location: Center of room
to ensure proper RF coverage of area.
A
Install the 1/2 in NPT to 20 mm conduit adapter (provided) onto the
PowPak Dimming Module with 0 –10 V.
B
The PowPak Dimming Module with 0 –10 V can be installed in a
junction box or marshalling box using the conduit nut (provided) or
with mounting screws (not provided). Please consult local and national
NEU
electric codes for proper installation.
Sample LED
C
Once installed, energize the PowPak Dimming Module with 0 –10 V.
HOT
driver shown
D
Use the Toggle button " u " to toggle between high-end and OFF to
+
verify LED driver / ballast wiring.
–
E
Use the Raise "▲" and Lower " " buttons to verify control wiring.
Download the Lutron Vive app.
C
Open the app and follow the instructions.
vive.lutron.com
• Ensure that the breaker(s) to the PowPak Dimming Module with 0 –10 V are energized.
• Ensure that the PowPak Dimming Module with 0 –10 V switched hot lead is wired to the lighting fixture(s).
• Ensure that the PowPak Dimming Module with 0 –10 V control lines are wired to the lighting fixture(s).
Reset to factory defaults.
• Ensure that 0 –10 V control lines are wired properly.
• Ensure that fixture does not require an inverted signal (10 – 0 V control).
• Ensure that the breaker(s) to the PowPak Dimming Module with 0 –10 V and ballasts are energized.
• Ensure that Wireless Transmitters are associated to the PowPak Dimming Module with 0 –10 V.
Reset to factory defaults.
• The maximum number of Wireless Transmitters have been associated to the PowPak Dimming Module with 0 –10 V. To remove a previously set up Wireless
Transmitter, tap a Wireless Transmitter button three times; on the third tap hold for three seconds and then tap three more times.
Customer Assistance
At least one 0 –10 V LED Driver or Fluorescent Ballast
Consult third-party 0 –10 V fixtures installation guide for fixture-specific wiring.
For mounting and wiring best practices see Lutron Application Note #620 (P/N 048620).
+
Link
Cal.
Test
Radio Powr Savr Daylight Sensor
60 mA maximum for the control lines. Switches up to 8 A total.
May be pre-installed in light fixture.
(1 maximum)
Line / Hot (Brown)
Neutral (Blue)
Wiring a Lever
Operated Connector
When wiring lever
operated connectors
(2 supplied) use
2.5 mm
2
to 4.0 mm
2
(14 AWG to 12 AWG) solid
or stranded copper wire.
1
3
10 mm
2
Note: For further information on set up, programming, and troubleshooting with a Vive
system, please refer to the installation instructions included with the Vive hub or visit
www.lutron.com/vive-europe
Note: For programming the PowPak Relay Module with 0 –10 V without a Vive hub see
.
reverse side
X
www.lutron.com/support
Switched Line (Black)
Neutral (Blue)
To Fixtures
– (Gray)
+ (Violet)
0 – 10 V to Fixtures
Conduit Nut
1/2 in NPT to
20 mm Conduit
Adapter
www.lutron.com /vive