Descargar Imprimir esta página
Lutron PowPak RMJS-8T-DV-B Instalación
Lutron PowPak RMJS-8T-DV-B Instalación

Lutron PowPak RMJS-8T-DV-B Instalación

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

PowPak
|
Installation
Dimming Module with 0 –10 V
Part of the Vive Family
RMJS-8T-DV-B
120 / 277 V~ 50 / 60 Hz 8 A
UL 2043 Plenum Rated
URMJS-8T-DV-B
0 –10 V Control: 10 V- 60 mA
Compatible with ANSI E1.3 2001 (R2006), IEC 60929 Annex E
Note for Replacement:
RMxS and URMxS - the "S" model can replace the
non-"S" model
Important Notes: Please read before installing.
For installation by a qualified electrician in accordance with all local and
national electrical codes.
• Note: Use copper conductors only.
• Check to see that the device type and rating is suitable for the application.
• DO NOT install if product has any visible damage.
• If moisture or condensation is evident, allow the product to dry completely
before installation.
• Operate between 32 °F and 104 °F (0 °C and 40 °C) ambient.
• 0% to 90% humidity, non-condensing.
• For indoor use only.
PowPak
Dimming Module
Install in center of room to
maximize RF coverage.
Radio Powr Savr
Occupancy
Sensor
PowPak
30 ft
Dimming
(9 m) max
Module
Pico
Remote
Control
40 ft (12 m)
All Wireless Transmitters must be installed within 30 ft (9 m)
of the PowPak Dimming Module with 0 –10 V.
Default Functionality
Occupancy Sensors
Occupied: All lights 100%.
Unoccupied: All lights off.
Daylight Sensor
All lights dim in response to daylight.
Link
Cal.
Test
Wireless Controls
On
All lights 100%
Favorite All lights 50%
Off
All lights off
Lutron Electronics Co., Inc. 7200 Suter Road
Coopersburg, PA 18036-1299 USA
Required Components
For each system, ensure that you have:
One PowPak Dimming Module
At least one Wireless Transmitter
041588
041588
Rev. A
Rev. A
04/2017
04/2017
Load Status LED
Raise
Toggle
+
Lower
Radio Powr Savr Occupancy/Vacancy Sensor
PowPak Dimming Module with 0 –10 V
(1 maximum)
(10 maximum)
Start Here
1
Mount, Wire, and Install 0 –10 V Devices
and Lighting Fixtures
Consult third-party device installation guide
WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit
breaker before installing the unit.
A Connect mains wiring (switched hot, neutral) to each fixture.
B Connect 0 –10 V control (+ and – ) to each fixture.
Green/Yellow
Fixture Earth
Neutral
Switched Line/Hot
+
Violet
Gray
To additional 0 –10 V fixtures
3
Programming with a Vive Hub
A Use a smart device to configure
B Open the Wi-Fi setting on the smart
the Vive hub.
Vive
Troubleshooting
Ballasts cannot be controlled locally from PowPak Dimming
Module with 0 –10 V.
Lights do not dim as expected.
Lights do not respond to Wireless Transmitter(s).
Lights are unstable at low-end or flash/flicker at turn-on or turn-off. • Adjust low-end trim.
Wireless Transmitter(s) cannot be associated to PowPak
Dimming Module with 0 –10 V.
Pico Remote Control
(10 maximum)
2
Install PowPak Dimming Module with 0 –10 V
Suggested Installation Location: Center of room to ensure proper
RF coverage of area.
A PowPak Dimming Module with 0 –10 V can be installed in a junction box
or marshalling box using the conduit nut (provided) or with mounting
screws (not provided). Please consult local and national electric codes
for proper installation.
If installing unit inside a junction box, please see Application Note #423
at www.lutron.com/TechnicalDocumentLibrary/048423.pdf
B Once installed, energize the PowPak Dimming Module with 0 –10 V.
NEU
C Use the Toggle button " u " to toggle between high-end and OFF to
Sample
HOT
ballast shown
verify ballast wiring.
+
D Use the Raise " " and Lower " " buttons to verify control wiring.
C Open a Safari
device and select the network that is
on the smart device. Type
similar to Vive-1a2b3c.
vive.lutron.com in the address bar.
Vive
• Ensure that the breaker(s) to the PowPak Dimming Module with 0 –10 V are energized.
• Ensure that the PowPak Dimming Module with 0 –10 V switched hot lead is wired to the lighting fixture(s).
• Ensure that the PowPak Dimming Module with 0 –10 V control lines are wired to the lighting fixture(s).
Reset to factory defaults.
• Ensure that 0 –10 V control lines are wired properly.
• Ensure that fixture does not require an inverted signal (10 – 0 V control).
• Ensure that the breaker(s) to the PowPak Dimming Module with 0 –10 V and ballasts are energized.
• Ensure that Wireless Transmitters are associated to the PowPak Dimming Module with 0 –10 V.
Reset to factory defaults.
• The maximum number of Wireless Transmitters have been associated to the PowPak Dimming Module with 0 –10 V. To remove a previously set up Wireless
Transmitter, tap a Wireless Transmitter button three times; on the third tap hold for three seconds and then tap three more times.
Customer Assistance www.lutron.com/support
At least one 0 –10 V Fluorescent Ballast or LED Driver
Consult third-party 0 –10 V fixtures installation guide for fixture-specific wiring.
For mounting and wiring best practices see Lutron Application Note #620 (P/N 048620).
+
Link
Cal.
Test
60 mA maximum for the control lines. Switches up to 8 A total. May be pre-installed
in light fixture.
Note: All drivers and ballasts used with Vive wireless controls must comply with the
Radio Powr Savr Daylight Sensor
limits for a Class A device, pursuant to Part 15 of the FCC rules.
(1 maximum)
or Chrome
browser
D Follow the instructions on the screen
®
TM
to set up your system.
vive.lutron.com
vive.lutron.com
Junction Box
Line/Hot
(Black)
Switched Line/Hot (Red)
To Fixtures
Neutral
Neutral (White)
1/2 in (21 mm) Knockout Opening
Conduit Nut
0 –10 V to Fixtures*
+
* Use 18 AWG to 16 AWG (0.75 mm
2
to 1.5 mm
2
) solid wire only
Note: For further information
on set up, programming, and
troubleshooting with a Vive system,
please refer to the installation
instructions included with the Vive
hub or visit www.lutron.com/vive
Note: For programming the PowPak
Dimming Module without a Vive hub
see reverse side.
www.lutron.com

Publicidad

loading

Resumen de contenidos para Lutron PowPak RMJS-8T-DV-B

  • Página 1 Consult third-party 0 –10 V fixtures installation guide for fixture-specific wiring. Part of the Vive Family Rev. A Rev. A 04/2017 For mounting and wiring best practices see Lutron Application Note #620 (P/N 048620). 04/2017 Load Status LED Raise RMJS-8T-DV-B...
  • Página 2 Lutron, Pico, and PowPak are trademarks of Lutron Electronics Co., Inc., registered in the U.S. and other countries. Radio Powr Savr and Vive are trademarks of Lutron Electronics Co., Inc. Safari is a trademark of Apple Inc., registered in the U.S.
  • Página 3 PowPak de 0 –10 V. précédemment, appuyez sur le bouton du transmetteur sans fil trois fois ; la troisième fois, maintenez le bouton trois secondes puis appuyez de nouveau trois fois. Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 USA...
  • Página 4 Lutron, Pico, et PowPak sont des marques déposées de Lutron Electronics Co., Inc., enregistrées aux États-Unis et dans d’autres pays. Radio Powr Savr et Vive sont des marques déposées de Lutron Electronics Co., Inc. Safari est une marque déposée de Apple Inc.,...
  • Página 5: Instalación

    PowPak con 0 –10 V. configurado, pulse tres veces un botón Transmisor inalámbrico; la tercera vez manténgalo pulsado durante tres segundos y luego púlselo tres veces más. Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 USA...
  • Página 6 Lutron, Pico, y PowPak son marcas comerciales de Lutron Electronics Co., Inc., registradas en E.U.A. y en otros países. Radio Powr Savr y Vive son marcas comerciales de Lutron Electronics Co., Inc. Safari es una marca comercial de Apple Inc.,...
  • Página 7 Fios previamente configurado, tocar ligeiramente três vezes num botão do Transmissor sem Fios; ao terceiro toque manter premido durante três segundos e, em seguida, tocar ligeiramente mais três vezes. Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 USA...
  • Página 8 Lutron, Pico, e PowPak são marcas comerciais da Lutron Electronics Co., Inc., registradas nos EUA e em outros países. Radio Powr Savr e Vive é uma marca comercial da Lutron Electronics Co., Inc. Safari é uma marca comercial da Apple Inc.,...

Este manual también es adecuado para:

Powpak urmjs-8t-dv-b