1. Manuales
  2. Marcas
  3. Metra Manuales
  4. Sistema Estéreo para Coches
  5. 99-5835G
  6. Instrucciones de instalación

Metra 99-5835G Instrucciones De Instalación

Ocultar thumbs Ver también para 99-5835G:
1
2
3
4
5
6
7
8
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Descargar este manual
KIT COMPONENTS
• A) Radio trim panel • B) Dash panel • C) Radio brackets • D) Pocket • E) Airbag light • F) (4) #8 x 3/8" Phillips truss head screws
• G) (2) #8 x 3/8" Phillips pan head screws • H) (3) Metal "U" panel clips • I) (5) Metal "D" panel clips • J) (4) Small metal "D" panel clips • K) (4) Plastic panel clips
A
B
G
The World's best kits.
®
Ford Transit 2015-2019*
*For non-navigation model
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle
specific applications
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Radio trim panel is painted gray
C
D
H
I
metraonline.com
E
F
J
K
© COPYRIGHT 2021 METRA ELECTRONICS CORPORATION
99-5835G
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . .................................................2
Kit Preparation . ......................................................2
-ISO DDIN radio provision . ....................................3
Final Assembly . ......................................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: 70-5524
Antenna Adapter: 40-EU10
Visit MetraOnline.com for audio/video and steering wheel
control interface options.
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Socket wrench • T-20 Torx driver
Attention:
With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that
all installation connections are secure before
cycling the ignition to test this product.
REV. 7/27/21 INST99-5835G

Publicidad

Tabla de contenido
loading

Manuales relacionados para Metra 99-5835G

Resumen de contenidos para Metra 99-5835G

  • Página 1: Tabla De Contenido

    With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections are secure before cycling the ignition to test this product. The World’s best kits. ® metraonline.com © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/27/21 INST99-5835G...

  • Página 2: Dash Disassembly

    DASH DISASSEMBLY KIT PREPARATION 1. Unclip the dash panel above the radio. 1. Secure the factory vents to the radio 3. Attach the (4) plastic panel clips (Figure A) trim panel using the (2) #8 x 3/8" provided to the radio trim panel. Phillips pan head screws provided. (Figure B) 2. Remove (2) T-20 Torx screws securing the (Figure A) 4. Attach the (12) metal panel clips factory radio/trim panel. (Figure B) 2. Snap the factory hazard button into the provided to the dash panel. (Figure C) 3. Unclip the factory radio/trim panel from radio trim panel. An airbag light blank the dash, unplug and remove. (Figure B) has been included for models without a Continue to Kit Assembly 4. Remove (1) T-20 Torx screw per vent then (Figure B) passenger airbag indicator. (Figure A) unclip and remove the vents from the factory radio/trim panel. (Figure C) 5. Unclip and remove the hazard switch assembly from the factory radio/trim panel. (Figure D) Continue to Kit Preparation (Figure C) (Figure A)

  • Página 3: Kit Assembly

    1. Cut the shaded portion from the 3. Secure the radio into the dash. sub-dash of the vehicle to allow the 1. Attach the pocket to the radio brackets 4. Snap the radio trim panel over the radio radio to fit. (Figure A) using the (4) supplied #8 x 3/8" Phillips and then reassemble the dash in reverse 2. Locate the factory wiring harness and truss head screws. (Figure A) order of disassembly. antenna connector in the dash and 2. Remove the metal DIN sleeve and trim complete all necessary connections to ring from the aftermarket radio. the radio. Metra recommends using the 3. Slide the radio into the completed proper mating adapter from Metra and/ (Figure A) assembly and then secure it using the or AXXESS. Test the radio for screws supplied with the radio. proper operation. (Figure B) Continue to Final Assembly ISO DDIN radio provision 1. Attach the radio brackets to the radio (Figure B) using screws supplied with the radio. (Figure C)
  • Página 4 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians The World’s best kits. metraonline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/27/21 INST99-5835G...
  • Página 5 Asegúrese de que todas las conexiones de instalación estén seguras antes de realizar un ciclo de encendido para probar este producto. The World’s best kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/27/21 INST99-5835G...

  • Página 6: Desmontaje Del Tablero

    DESMONTAJE DEL TABLERO PREPARACIÓN DEL KIT 1. Desenganche el panel del tablero encima 1. Atornille las rejillas de fábrica al panel 3. Instale los (4) ganchos de plástico del radio. (Figura A) de moldura del radio usando los (2) para panel incluidos en el panel de la tornillos Phillips #8 de 3/8"...

  • Página 7: Ensamble Del Kit

    (Figura A) 3. Deslice el radio hacia adentro del acoplamiento de Metra y/o de AXXESS. ensamble completo y después sujételo Pruebe el radio para verificar si con los tornillos suministrados con el funciona bien.
  • Página 8 Tenga el vehículo separado y listo para realizar los pasos de solución de problemas antes de ponerse en contacto con el soporte técnico de Metra / Axxess. EL CONOCIMIENTO ES PODER Mejore sus habilidades de instalación y...

Tabla de contenido