Cadiz Eco
Models : CDE2ECC and CDE3ECC
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Model
Description
CDE2ECC Electronic Climate Control
CDE3ECC Electronic Climate Control
Important Safety Advice
If the appliance is damaged, check immediately with the
supplier before installation and operation.
Warning – This appliance must not be used in a bathroom.
Warning – Do not use this heater in the immediate
surroundings of a bath, a shower or a swimming pool.
Warning – This heater must not be located immediately
below a fi xed socket outlet.
Warning – Do not use in areas where petrol, paint or
fl ammable liquids are used or stored.
Follow these instructions carefully.
The heater carries a warning symbol to alert the
user to the risk of fire that exists if the heater is
accidentally covered.
WARNING – THIS APPLIANCE MUST BE EARTHED
The appliance is not intended for use by children or
other persons without assistance or supervision if their
physical, sensory or mental capabilities prevent them from
using it safely. Children should be supervised to ensure
that they do not play with the appliance.
Do not put objects through the openings of the appliance.
This could lead to functional faults, possibly to the ignition
of the object.
If the mains lead is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
Unplug the heater when not required for long periods.
Note that due care and consideration must be taken
when using this heater in series with a thermal control, a
program controller, a timer or any other device that
switches on the heat automatically, since a fi re risk exists
when the heater is accidentally covered or displaced.
General
The heater is designed for operation on an AC electricity supply, and is
suitable for use in domestic dwellings and similar indoor locations.
Always ensure that the appliance is stood on a fi rm, level base near to,
but not directly beneath, a suitable fi xed socket outlet.
The heater is fi tted with wheels, castors and a handle for ease of
movement. Selector switches provide a choice of heat output and an
adjustable thermostat enables the room temperature to be controlled
accordingly. It is supplied with a cord and plug ready for use.
The supply cord should be uncoiled before use (see 'Storage').
DO NOT pull the heater along by the mains lead.
Important - The heater must only be operated with the wheels and
castors fi tted and in the upright position as shown in Fig. 1.
Warning – The heater complies with stringent safety standards but to
ensure effi cient operation SURFACES OF THE HEATER WILL BECOME
HOT AND CONTACT WITH THESE AREAS SHOULD BE AVOIDED,
particularly between the air outlet slots on the top and sides.
The control panel area is designed to be at a far lower temperature to
allow the safe operation of the controls at any time.
Momentary contact with any part of the heater should not cause injury.
However aged, infi rm persons or young children should not be left
unsupervised in the vicinity of the heater.
Please Note – After switching the heater on for the fi rst time and after
an extended period of non-use a smell may be noticed, this is quite
normal – the fumes are non-toxic and will quickly disappear. We
recommend that you open a window to ventilate the room when using
the heater during this time.
Used in an environment where background noise is very low, it may be
possible to hear a sound which is related to the element. This is normal
and should not be a cause for concern.
Watts
Positioning the Heater
2000
Select the position for the heater ensuring there is clearance from any
3000
furniture and fi ttings of at least 300mm above the heater and 150mm
each side. The appliance should only be operated on a fl at stable
surface.
Operation
Important – Objects or clothing must not be placed on this heater. Before
using the heater ensure that all warnings and instructions have been
read carefully.
To bring the heater into use plug it in. Neon indicating lights located at
the controls area will glow when the appliance is actually heating.
Controls
On/Off button -
elements.
When the On/Off button is activated a neon light 'x' illuminates
below the control button.
Electronic Climate Control
Operation
The electronic control allows MANUAL and AUTO operation.
In MANUAL ON mode there are three heat settings :
L/H Side Heat, R/H Side Heat and High Heat
In AUTO mode the heater comes on as per the programmed timer
settings (see Setting programs). At any point if the heater is active i.e.
heat is being produced, the ' ' neon is lit - see Fig. 4.
Initial Operation
When the heater is connected to the mains the ' ' neon will be lit and
the display is blank. Press the '
heat set to 35
Note: All display characters are displayed in Fig. 13.
Standby Mode
With the heater ON if the '
standby mode, heater switches off, the display goes blank and only
the MAINS ON neon ( ) remains lit. On pressing the '
the heater will come on in the mode and with the settings it had prior to
going into standby mode.
Setting Time
To set the time press 'P' and the '
- see Fig. 9.
1.
Press the ' ' or '
2.
Press ENTER. The display will return to the state prior to entering
set time.
N.B. If no keys are pressed after 4 minutes the display will revert to the
state prior to entering set time.
Manual Operation
Pressing ' ' from the default HIGH screen (Fig. 8) brings the heater
into AUTO mode - see 'Setting the Timer Programs'. Press again to put
the heater into OFF mode - see Fig. 6. Press again for left hand side
heat (
hand side heat (
user full circle to FULL heat mode (
Setting the Desired Temperature
The desired temperature can be set using the ' ' or '
temperature can be set from 5
display. When the temperature is reached the heater will automatically
switch OFF. If the ambient temperature drops the heater will come on
again automatically. Note the electronic climate control device conserves
energy and assists with temperature regulation e.g. if the heater is set
to HIGH heat and the temperature is set to 28
switch to a lower heat setting. Then at 28
completely.
- 4 -
This button controls the electricity supply to the
- see Fig. 4
' button and the display goes to full
o
C - see Fig. 8.
' button is pressed, the heater will go into
' appears with the digits fl ashing
' until the correct time is displayed.
appears on LCD display - see Fig. 7). Press again for right
appears on LCD display). Press again brings the
o
C to 35
o
C and this will be shown on the
' button again
appears on LCD display).
' keys. The
o
C, at 27
o
C the heater will
o
C the heater will switch off