Technical Specifications; Preliminary Checks - Genius RAINBOW 324 C Guía Para El Instalador

Thank you for choosing our product. GENIUS is sure you will get the
performances you expect to satisfy your requirements. All our products
systems, strengthened by being part of a world leading group in this
sector.
containing all the images for the installation.
The automated systems of the RAINBOW family are electro-mechanical
barriers which have been designed and bui lt t o control vehi cle
accesses.
The control unit is located on the upper part of the automated system and
can be rotated to facilitate wiring and setting operations. Suitable facilities
for the photocells (Orion) and the key selector (Quick) are present on the
housing. Both on the housing and on the rods you can install luminous
Thanks to the various types of rods available, these can be used in
very different types of accesses, from a minimum of 2 meters up to a
maximum of 7 meters.
A handy release device, protected by customised key, enables you to
move the rod by hand in the event of a power cut.
Thanks to the use of 24V motors and of the encoder (standard supplied),
all automated systems of the RAINBOW family are able to guarantee
very high safety levels.
IMPORTANT WARNINGS FOR THE INSTALLER
Carefully read the whole manual before beginning to install the
operator.
Store the manual for future reference.
are only valid if the instructions given in this manual are strictly
observed and only GENIUS accessories as well as safety device
are used.
To guarantee an adequate level of safety of the automated system,
the use of a control unit with an adjustable electronic clutch is
necessary due to the lack of a mechanical clutch .
The automated system was designed and built to control vehicle
access. Avoid any other use.
The operator cannot be used to move safety exits or gates installed
on emergency routes (escape routes).
Do not transit when the rod is moving.
1. DESCRIPTION
Pos.
Upright
Panel
Foundation plate (sold as a separate part)
Cover
Control unit enclosure
Rod (sold as a separate part according to installation requi-
rements)
Balance spring (sold as a separate part, number and type
Gearmotor
Encoder
Closing / opening travel limits
Safety switch for opening panel
Red edge (cover for optional luminous strip)
Release device
Compartment for buffer batteries (not supplied)

1.1 TECHNICAL SPECIFICATIONS

RAINBOW Model
Power supply voltage
Motor supply voltage (V )
Max. power at thrust (W)
Motor rated power (W)
Max. torque at 24V (Nm)
Operating rated torque (Nm)
Description
324 C 524 C 724 C
230V~ 50Hz / 115V~ 60Hz
24
280 480
160 220
155 140 370
30 75 140
RAINBOW Model
Opening / closing nominal time (sec)
Rod max. length (m)
Type and use frequency at 20°C
Daily max. cycles (cycles)
Operating ambient temperature (°C)
Noise (dBA)
Protection class
Operator weight (Kg)
Dimensions
Time according to the type of deceleration being set.
Length referred to the passage width, rod length +300mm approx for
Rainbow 324C and Rainbow 524C; rod length +400mm approx for
Rainbow 724C
The tables below indicate the product life, expressed in number of cycles,
RAINBOW 324 C - RAINBOW 524 C
Rod and accessory
2 to 3 meters
4 meters
5 meters
3 meters with foot
4 meters with foot
5 meters with foot
3 meters with 2 m skirt
4 meters with 3 m skirt
5 meters with 4 m skirt
RAINBOW 724 C
Rod and accessory
4 meters
5 meters
6 meters
7 meters
4 meters with foot
5 meters with foot
6.5 meters with foot
4 meters with 2 m skirt
5 meters with 3.5 m skirt
6.5 meters with 5 m skirt
The product life has been calculated at a temperature of 20°C on
indicated in the instructions.
2. ELECTRICAL PREPARATIONS (standard system)
Pos. Description
Operator (power supply)
TX photocell
RX photocell
Key-selector
Always separate connection cables of low-voltage accessories
from power cables. To prevent any interference whatsoever, use
separate sheaths.
3. INSTALLING THE AUTOMATED SYSTEM

3.1. PRELIMINARY CHECKS

sure the following conditions are observed:
When moving, the beam must not, on any account, meet any obstacles
or overhead cables.
There must be no pipes or electrical cables in the plinth excavation
Page 7
324 C 524 C 724 C
2 to 3 4 to 8 7 to 11
3 5 7
Semi-intensive
1500 1000 500
-20 +55
<70
IP 54
66 72
3
Life (No. of cycles)
1.500.000
1.300.000
1.100.000
1.300.000
1.100.000
800.000
1.300.000
1.100.000
800.000
Life (No. of cycles)
1.300.000
1.100.000
850.000
500.000
1.100.000
850.000
500.000
1.100.000
850.000
500.000
Cable section
3x1.5 mm 2
2x0.5 mm
2
4x0.5 mm
2
2x0.5 mm 2