Black and Decker FSMH1621 Manual De Instrucciones página 6

ENGLISH
Attaching the hand held steam cleaner (Fig. C)
Holding the back of the steam mop body (9) Push the
u
hand held steam cleaner (5) firmly into the steam mop
body (9) until it clicks into place.
Caution! Always ensure the handle command lights up to
confirm the unit is docked.
Warning! Inspect that the seal (22 Fig. H) on the steam noz-
zle (4) before fitting the hand held steam mop to the steam
mop body. If the seal is missing or damaged then please
contact your nearest authorised repair agent. Do not use the
appliance.
Removing the hand held steam cleaner (Fig. C)
Push the release button (19) down and pull the hand held
u
steam cleaner (5) away from the steam mop body
Attaching a cleaning pad (Fig. D)
Replacement cleaning pads are available from your Black &
Decker dealer:-
Steam head cleaning pad - cat. no. FSMP20-XJ).
Place a cleaning pad (12) on the floor with the 'hook &
u
loop' side facing up.
Lightly press the steam mop down onto the cleaning pad
u
(12).
Caution! Always place your steam mop on the resting mat
(13) with the handle (10) in the upright position when station-
ary and make sure the steam mop is turned off when not in
use.
Removing a cleaning pad (Fig. E)
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop. Do not wear slippers or
open toed footwear.
Return the handle (10) to the upright position and turn the
u
steam mop 'OFF'.
Place the steam mop on the resting mat and wait until it
u
cools down. (approximately five minutes)
Place the front of your shoe onto the cleaning pad removal
u
tab (21) and press down firmly.
Lift the steam mop up off the cleaning pad.
u
Caution! Always place the steam mop on the resting mat (13)
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Filling the water tank (Fig. F)
This Steam cleaner incorporates an anti-calc system to help
prolong the life of the system.
Note: Fill the water tank with clean tap water.
Note: In areas of very hard water, the use of de-ionised water
is recommended.
Open the filler cap (7) by flipping it down.
u
Using the jug, fill the water tank (8) with water.
u
6
(Original instructions)
Warning! Your water tank has a 0.35 litre capacity.
Re-fit the filler cap (7).
u
Note: Ensure the filler cap is firmly secured.
Note: When not in use, the jug (18) may be clipped to the
handle for convenient storage.
Note: Do not use chemical cleaners with your steam mop..
Attaching the carpet glider (Fig. G) (For use on
carpets only)
Place carpet glider on the floor.
u
Attach a cleaning pad to the unit.
u
Lightly press the steam mop down onto the carpet glider
u
(14) until it clicks into place.
Caution! Always place the steam mop on the resting mat (13)
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Removing the carpet glider (Fig. G)
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
Return the handle (10) to the upright position and turn the
u
steam mop 'OFF'.
Place the steam mop on the resting mat and wait until it
u
cools down. (approximately five minutes)
Place the front of your shoe onto the carpet glider removal
u
tab (33) and press down firmly.
Lift the steam mop up off the carpet glider (14).
u
Caution! Always place the steam mop on the resting mat (13)
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Attaching the hose and accessories to the Hand
held steam cleaner (Fig. H & I)
Warning! Inspect the seal (22) on the steam nozzle (4) and
hose (23) before each use. If the seal is missing or damaged
then please contact your nearest authorised repair agent. Do
not use the appliance.
Attaching the hose (Fig. G)
Press in the clips (24) on either side of the hose (23).
u
Press the hose (23) onto the steam nozzle (4) and release
u
the clips (24).
Important! Ensure that the hose (23) is securely fastened
before using the hand held steam cleaner. If steam escapes
from the joint then the hose is not correctly fit, allow the unit to
cool then remove and re-fit the hose.
Attaching the variable steam jet nozzle (Fig. I)
Press in the clips (26) on either side of the variable steam
u
jet nozzle (27).
Press the variable steam jet nozzle onto the steam nozzle
u
(4) or the hose (23) and release the clips (26).