Black and Decker KC2000 Manual Del Usuario página 6

ENGLISH
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battery (fig. B)
KC2000
To fit the battery (5), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the two release buttons (6)
simultaneously while at the same time pulling the battery
out of the receptacle.
KC2002
To fit the battery (5), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release button (10) while
at the same time pulling the battery out of the receptacle.
Fitting and removing tool heads (fig. C)
The different tool heads can be easily exchanged.
Lock the tool by setting the forward/reverse slider (2) to
the centre position.
To remove a tool head, depress the head release button (3)
and take the head off the tool.
To fit a tool head, line it up with the tool as shown and
push it onto the tool until it snaps into place.
Fitting and removing a drill bit or screwdriver bit
(fig. A & D)
The drill/screwdriver head is fitted with a keyless chuck to
allow for an easy exchange of bits.
Lock the tool by setting the forward/reverse slider (2) to
the centre position (fig. A).
Open the chuck by turning the front part (15) with one
hand while holding the rear part (16) with the other (fig. D).
Insert the bit shaft (17) into the chuck.
Firmly tighten the chuck by turning the front part (15) with
one hand while holding the rear part (16) with the other.
This tool is supplied with a double-ended screwdriver bit in
the bit holder (4) (fig. A).
To remove the screwdriver bit from the bit holder, lift the
bit from the recess.
To store the screwdriver bit, firmly push it into the holder.
Fitting and removing a saw blade (fig. F & G)
Lock the tool by setting the forward/reverse slider (2) to
the centre position (fig. F).
To fit a saw blade, lift the lever (18) and hold it in this
position (fig. G).
6
Insert the saw blade into the holder as shown. Make sure
that the teeth are pointing to the front.
Release the lever.
To remove the saw blade, lift the lever (18) and pull the
saw blade from the holder.
Fitting and removing sanding sheets (fig. F & I)
The sanding head uses pre-cut sanding sheets.
Lock the tool by setting the forward/reverse slider (2) to
the centre position (fig. F).
Before fitting a new sheet, remove the two additional
diamond tips (20) (fig. I).
To fit a sanding sheet, line it up with the sanding base as
shown.
Press the sheet firmly and evenly onto the sanding base,
making sure that the holes in the sheet coincide with the
holes in the base.
To remove the sheet, pull it off the sanding pad.
Warning! Never use the sanding head without a sanding
sheet or accessory in place.
Replacing the diamond sanding tip (fig. F & J)
Sanding sheets are supplied with two replacement diamond
tips. The diamond tip can be reversed when worn. When both
sides are worn, replace the diamond tip.
Lock the tool by setting the forward/reverse slider (2) to
the centre position (fig. F).
To reverse the tip, remove it, turn it 180° and press it back
onto the base as shown (fig. J).
To replace the tip, pull the old tip off the base and press a
new one onto the base.
Warning! When removing the tip from the pad, be careful not
to pull the pad off the sanding base.
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (fig. A)
The battery needs to be charged before first use and whenever
it fails to produce sufficient power on jobs that were easily
done before. A new battery, or a battery that has not been
used for an extended period of time, achieves full performance
only after approx. 5 charging and discharging cycles. The battery
may become warm while charging; this is normal and does not
indicate a problem. After normal use, a charging time of
60 minutes will provide sufficient power for most applications.
However, further charging for up to 90 minutes could
significantly increase the use time, depending on the battery
and charging conditions.