Tippmann Triumph XL Manual Del Usuario página 6

TRIUMPH eXT Trigger Operating Instructions
E
Read And Follow these Trigger Operating Instructions before attempting to
operate a Triumph eXT Marker.
N
TM
STEP 1: Prepare the marker for safety before any programming:
G
Install the Air Supply and load the hopper with paintballs only after you
L
have successfully installed the battery,
electronics operation; have the barrel sleeve installed and
I
the "SAFE" position. Read each step completely before performing step:
S
STEP 2: To Install the Battery:
H
1) Prepare the marker for disassembly:
air supply removal instructions on page 13 and never disassemble a marker
that is under pressure.
2) To Remove Battery Clip / old battery from marker:
Cover bolt =(5/8") and slide Battery Cover
(see page 14).
Lift battery out of Grip Frame being careful not to
pull wires off of internal components.
remove old battery from battery clip connector.
3) To install new battery:
battery connector and be sure wires lay flat inside the
cutout area of the receiver (as shown on page 18).
Carefully insert your new battery, wire attached,
into the receiver.
Slide Battery Cover onto Grip Frame, insert and
tighten Battery Cover Bolt
Battery installation is complete.
STEP 3: To turn ON the trigger electronics.
To turn on the electronics, use a small object like
an allen wrench to press and hold the power button
(for about 5 seconds) until the green LED light comes
on then release the power button.
Your marker is now ready for normal operation in
the SEMI-AUTO Firing Mode: 1 pull of the trigger fires 1 time (This is the
Factory Default Firing Mode Setting).
NOTE: If pressing power button failed to turn on LED light, see
troubleshooting on page 9.)
• Low battery indicator - the LED light turns red when battery is low.
STEP 4: To turn OFF the trigger electronics.
Press and hold the power button until the LED turns off, then release
the Power Button. NOTE: The trigger electronics are set to shut-off
automatically after a prolonged period of inactivity.
are familiar with the eXT
First follow the unloading and
Remove Battery
off the Grip Frame
Carefully
Attach 9v battery to
NOTE: Low battery
indicator - the LED light
turns red when the
.
battery is low.
Power
Button
8
eXT Trigger Operating Instructions
(continued on page 9)
EXT M Trigger Operating Instructions (continued from page 8)
STEP 5: To select a new firing mode:
With the electronics turned on, each press / release of the power button
will change the firing mode to the next firing mode in the menu: (the LED
will flash 1, 2, 3 or 4 times to identify the mode you have selected).
THE 4 FIRING MODES ARE:
Default firing mode:
1) SEMI-AUTO = 1 pull / release of the trigger fires 1 time.
safety in
1 flash of the LED light indicates SEMI-AUTO mode.
Press mode button to get:
2) TRIPLE FIRE = (3 shots in 0.25 seconds for one pull of the trigger).
2 flashes of the LED light indicates TRIPLE FIRE mode.
Press mode button to get:
3) FULL-AUTO NORMAL = (12 shots per second): To fire in Full-Auto Normal
mode you must pull the trigger 4 single pulls within 1.00 second and hold
the 4th pull to fire 12 shots per second until you release the trigger).
3 flashes of the LED light indicates FULL-AUTO NORMAL mode.
Press mode button to get:
4) FULL-AUTO FAST = (15 shots per second): To fire in Full-Auto Fast
mode you must pull the trigger 4 single pulls within 1.00 second and hold
the 4th pull to fire 15 shots per second until you release the trigger).
4 flashes of the LED light indicates FULL-AUTO FAST mode.
Press mode button to get:
1) SEMI-AUTO (Default firing mode - see above).
POWER BUTTON - TROUBLESHOOTING
LED
PROBLEM: The LED light does not light when you push the power button.
1) Battery may be disconnected.
2) Battery may be bad -
3) Internal wire may be disconnected. Do NOT disassemble a marker while
it is pressurized with air.
follow Grip frame disassembly (see page 17); / wire inspection and
reassembly instructions on pages 18/19. NOTE: If a problem still exists,
call Tippmann
Check battery clip connection.
Replace battery.
To inspect wire connections inside the receiver:
Service Department at 1-800-533-4831.
®
9
E
N
G
L
I
S
H