Marker Disassembly / Assembly - Tippmann Triumph XL Manual Del Usuario

Marker Disassembly / Assembly:

disassembly and assembly of paintball markers, we suggest having these services
E
performed by an authorized Tippmann
disassemble or assemble this marker. Hand start screws and bolts and do not
N
over tighten and strip threaded parts. First follow unloading and air supply removal
G instructions on page 13. Do not pressurize a partially assembled paintball marker.
Put the marker in the uncocked position. If marker is cocked, hold the bolt cocking
L
handle - then pull the trigger and release handle forward
I
S
H
Bolt = 1 1/16"
Bolt = 7/8"
Bolt = 5/8"
Bolt = 1/2" Flat Head
Bolt = 1/2" Round Head
Screw = 1/2" + Head
To remove the barrel
To remove the Grip Frame
disconnect the tank adapter
and pull battery cover off.
Remove the 2 Grip Frame
bolts =(1 1/16") / =(1/2")
and remove the Grip Frame
by carefully tilting it side to
side as you work it down off
the receiver lug , back and
out of the receiver .
TO CHECK THE RECEIVER INTERNAL PARTS:
Cover (or Front Grip on XT and eXT).
=(1/2" rounded head) and slide Front Grip Cover
off. NOTE: It is not necessary to disassemble the 2 front Grip Halves at any time.
To Remove the Receiver Cover
(1 from left side and 1 from right side) holding the Receiver Cover. At
these 2 points, spread Receiver Cover apart enough to carefully slide it
off the front of the receiver while observing how its inner guides align to
the guides of the receiver (NOTE: at reassembly you will spread apart
and slide the cover into place with guides aligned the same way).
NOTE: If you are not proficient in the
® Technician. Do not use power tools to
to uncock the marker.
: twist the barrel counterclockwise.
: Remove 2 tank adapter bolts
. Remove the Battery Cover bolt
Remove the Front Grip
Remove the front Grip bolt
(or Front Grip
: Remove the 2 screws
14
Disassembly / Assembly (continued on page 15)
Disassembly / Assembly (continued from page 14)
GAS LINE ACCESS:
The Gas line
Line with In Line Expansion
Chamber on models XT
and eXT) is located in the
Mid-Grip .
To remove Mid-Grip
from the receiver:
Remove 2 bolts
holding it to the receiver.
(Nuts for these 2 bolts
will remain in place in
right Mid-Grip half and
need not be removed).
Remove 4 screws
holding Mid-Grip halves
together.
come off right side. (NOTE: At reassembly, place square nut
Mid-Grip half. Also be sure tank adapter alignment lug-pin
both left and right Mid-Grip halves).
=(7/8") to
=(5/8")
)
To remove Tank Adapter
necessary to remove the tank adapter to disassemble the receiver.) Hold
the Gas Line fitting with a wrench and unscrew tank adapter
/
Reinstalling Tank Adapter
o-ring and if damaged, replace with a new one. Clean and oil the gas line o-ring.
Hold Gas Line fitting with wrench and hand start Tank Adapter onto gas
line fitting and slowly screw it on until tank adapter aligns with bottom of
Grip Frame and is snug (do not over tighten and strip threaded parts).
(or Gas
=(5/8")
Bolt = 5/8"
Screw = 1/2" + Head
Lift left Mid-Grip half off and
from the gas line
to the gas line
15
Disassembly / Assembly (continued on page 16)
E
N
G
L
I
S
H
right Mid-Grip half will
in right
fits into
: (NOTE: it is not
from it.
: Check the gas line