Moulinex LM6208FR Manual Del Usuario página 11

notice blender2:Mise en page 1
Diagram :
❸
Fit the lid seal (E5) around the lid (E6), lock the
lid on to the blender by turning anti-clockwise
(E4) and place the cap (E7) in the lid.
- Place the grid (A2) on the drip tray (A1).
- Slide the drip tray unit (A) into the motor unit
(D), into its housing (B).
- Plug the appliance in, turn it on and choose
the speed most suitable for your preparation
using the speed selection switch (C).
To stop the appliance, turn the speed switch
(C) to 0.
The lid and its cap must always be properly
fitted when the appliance is working.
Always hold your glass firmly on the grid.
To add ingredients while the blender is
operating , insert them through the feeder hole
in the lid (E6).
After use, if necessary, throw away the contents
of the drip tray (A1) and wash the drip tray unit
(A) carefully.
DISPENSING THROUGH THE TAP (F)
Diagram
❹
Two positions are possible, by pivoting the tap
(F1):
- When the lever faces downwards, you can
serve yourself by pressing it directly with a
glass.
- When the lever is facing upwards you can
serve yourself by pulling it with your hand and
the liquid will flow faster.
NB: To make thicker mixtures (such as
milkshakes or smoothies) flow better, set the
blender to speed 1 and then pull the pedal
forward). Turn the appliance off when you
have finished serving.
Clean the tap after each use (see Cleaning §)
If you do not need the tap, you can replace it
with the cap (J) (see diagram ❻), fitted on to
the sealing joint (E3).
USE OF THE ICE STICK (H)*
(according to model)
This accessory enables you to cool mixtures
down, or keep them cool.
- Fill the square part of the handle (H2) with
crystal salt right up to the brim (diagram ❺)
and then pour the salt into the container (H1).
- Fill the container (H1) with cold water.
- Screw the handle of the container on very
tightly and shake until the salt dissolves.
- Place the handle in the deep freezer (at least -
18°C), preferably in an upright position, until the
salt water mixture has frozen (12 hours
minimum).
- Make your preparation in the blender, and then
introduce the frozen ice stick (H) through the
26/02/08 14:54 Page 7
hole in the lid (E6), instead of the cap (E7). The
mixture will then be cooled.
- You can use the ice stick as a mixing stick to
help mix up your drinks, by introducing it
through the feeder hole in the lid (E6).
USE OF THE ACCESSORIES (K & L)
(according to model)
SPICE GRINDER ACCESSORY (K):
this accessory allows you:
- to grind up to 40 g of coffee in 30 seconds
maximum operating time;
- to grind or chop various spices, dried fruits and
nuts such as hazelnuts, walnuts, almonds or
dates in a matter of seconds. E.g. 50 g of dates
in 4 seconds.
GRATER ACCESSORY (L):
this accessory can reduce to powder nutmeg
and grate coconut, hard cheeses (eg 60g of
Parmesan) cut into small cubed pieces with a
30 second maximum operating time.
- These accessories are fitted with a safety lid
(M) which prevents access to the blades
during operation.
- Introduce the ingredients into the container (K
or L). Fit the lid (M) to the container of the
accessory (only one position is possible) and
turn it in a clockwise direction to lock it
(towards the closed padlock symbol), then fit
this assembly onto the blender body (D) (see
diagram ➒).
- Plug in the blender and set the speed selector
(C) to "pulse". Hold the lid during operation.
- To stop the blender, turn the speed selector (C)
to the "0" position and only remove the
accessory when the appliance has completely
stopped.
Turn the assembly upside down on the work
surface before unlocking the lid of the accessory
(K or L) (see diagram
The preparation may then be taken directly
from the lid, which acts as a bowl.
7
*
).
❿