Troubleshooting Guide; Technical Service - Health Zenith SL-5525 Manual De Instrucciones

SYMPTOM POSSIBLE CAUSE
Light will not 1. Light switch is turned off.
come on. 2. Bulb is loose or burned out.
3. Fuse is blown or circuit breaker is
turned off.
4. Daylight turn-off is in effect (recheck
after dark) .
5. Incorrect circuit wiring, if this is a
new installation.
6. Re-aim the sensor to cover desired
area.
Light comes on 1. Light control may be installed in a
in daylight. relatively dark location.
2. Light control is in test. (Set control
switch to an ON-TIME position.)
Light comes on 1. Light control may be sensing small
for no apparent animals or automobile traffic (re-
aim sensor) .
reason.
2. Sensitivity is set too high. (Reduce
sensitivity.)
Lights flash 1. Sensor is detecting its own light.
once, then stay (Reposition lamp to keep area be-
off in Manual low the sensor relatively dark.)
Mode.
Please call 1-800-858-8501 for assistance before returning product to store.
If you experience a problem, follow this guide. You may also want to visit our Web site at: www.desatech.com. If the
problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to:
DESA Specialty Products™
ATTN: Technical Service Specialty Products
P.O. Box 90004, Bowling Green, KY 42102-9004
* If contacting Technical Service, please have the following information available: Model Number, Date of
Purchase, and Place of Purchase.
This is a "Limited Warranty" which gives you specific legal rights. You may also have other rights which vary from state to state or
province to province.
For a period of ten years from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected
at no charge to you.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other
expendable items are not covered by this warranty. Unauthorized service or modification of the product or of any furnished component
will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss
of use, unauthorized service, or return shipping charges.
This warranty covers only DESA Specialty Products™ assembled products and is not extended to other equipment and components
that a customer uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WAR-
RANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY
PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUEN-
TIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON
THE PART OF DESA SPECIALTY PRODUCTS™ FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAM-
AGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some
states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. Proof of purchase is required for warranty claims.

TROUBLESHOOTING GUIDE

TECHNICAL SERVICE

No Service Parts Available for this Product
TEN YEAR LIMITED WARRANTY
SYMPTOM POSSIBLE CAUSE
Light stays on 1. The lamp is positioned too close to
continuously. the sensor or pointed at nearby ob-
jects that cause heat to trigger the
sensor. (Reposition the lamp away
from the sensor or nearby objects.)
2. Sensor is pointed toward a heat
source like an air vent, dryer vent, or
brightly-painted heat-reflective sur-
face. (Reposition sensor.)
3. Control is in Manual Mode. (Set to
Auto.)
Light flashes 1. Heat or light from the lamp may be
on and off. turning the Light Control on and off.
(Reposition the lamp away from the
sensor.)
2. Heat being reflected from other ob-
jects may be affecting the sensor.
(Reposition sensor.)
3. Light Control is in the Test mode and
warming up. (Flashing is normal un-
der these conditions) .
4. If eave installation, Light Shield not
installed properly. (Install Light Shield
according to instructions.)
4 595-5295-11