After Use - Black and Decker FSMH1321 Manual Del Usuario

ENGLISH
Steam Burst (Fig. C1) (only available with units
FSMH1310SM, FSMH13151SM)
Hints for optimum use
General
Steam Cleaning with the mop
Using Autoselect , choose from one of the following
applications by turning the Autoselect
required setting is selected.
Setting Mop
The steam mop will select the correct volume of steam
required for your particular cleaning operation.
Note: Always check you are using the correct setting before
using your steam mop.
aid in the removal of stubborn marks and stains.
During use, press the steam burst pedal to apply extra
cleaning power.
To revert back to normal setting press the pedal again.
Caution: Never use the steam mop without first attaching a
cleaning pad.
mop.
The easiest way to use the appliance is to tilt the handle
to a 45º angle and clean slowly, covering a small area at a
time.
Use water only with no additives or chemicals with your
steam mop. To remove stubborn stains from vinyl or
and some water before using the steam mop.
Fit hand held steam cleaner (5) to the steam mop body
(11)
side facing up.
Lightly press the steam mop down onto the cleaning pad
(13).
Connect the steam mop to the mains.
Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
10
Wood/Laminate
Stone/Marble
Tiles/Vinyl
TM
The floor head (12a) is equipped with a steam burst pedal to
u
u
Always vacuum or sweep the floor before using the steam
u
u
u
linoleum floors, you can pre-treat with a mild detergent
u
Place a cleaning pad (13) on the floor with the velcro 'loop'
u
u
u
u
(Original instructions)
dial (2) until the
Hand held
High temperature steam for
windows
Low temperature steam for
heavy grime
TM

 
  
Carpet refreshing

After use

Turn the Autoselect dial (2) until the required setting is
reached. After a few seconds steam will start to come out
of the steam head.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
It takes a few seconds for steam to enter the cleaning pad.
The steam mop will now glide easily over the surface to be
sanitized/cleaned.
Push and pull the steam mop slowly across the surface to
thoroughly steam clean each section.
the handle (8) to the upright position, making sure that it
Caution! It is important to monitor the water level in the
clean stand the mop upright making sure that the handle is
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
facing up.
lightly press the steam mop down onto the cleaning pad.
Lightly press the steam mop down onto the carpet glider
until it clicks into place.
Connect the steam mop to the mains.
Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
Turn the Autoselect dial (2) to the Wood/Laminate
setting.
Push and pull the steam mop slowly across the carpet to
thoroughly refresh each section.
handle (8) to the upright position and turn the unit OFF.
minutes).
Turn the Autoselect dial (2) to the OFF position.
Wait until the steam mop cools down.
Unplug the steam mop from the electrical wall outlet.
Empty the water tank.
remove the cleaning pad (13) and wash it ready for next
use (take care to follow the wash care instructions printed
on the cleaning pad).
TM
TM
TM
u
u
u
When you have finished using the steam mop, return
u
is supported and turn it 'OFF'. Wait until the steam mop
cools down (approximately five minutes).
water tank. To refill the water tank and continue to sanitize/
supported and turn the steam mop 'OFF'. Unplug the unit from
the electrical wall outlet, and refill the water tank.
Place a cleaning pad (13) on the floor with the 'loop' side
u
u
Place the carpet glider (12b) on the floor.
u
u
u
u
u
u
When you have finished using the steam mop, return the
u
Wait until the steam mop cools down (approximately five
u
u
u
u
u