Axxess AX-TOYCAM3 Instrucciones De Instalación

Installation Instructions for AX-TOYCAM3
AX-TOYCAM3
Toyota Back-Up Camera Retain/Add-On
2013-2016
• Retains the factory back-up camera to an aftermarket radio
• Allows an aftermarket camera to be added to the factory radio screen*
* Display and navigation model radios only
INTERFACE COMPONENTS
• AX-TOYCAM3 harness
APPLICATIONS
SCION Avalon
FRS 2016
Camry
iM 2016 Corolla
tC 2016 Highlander
Prius C
TOYOTA
Prius V
4-Runner 2014-2016 Rav-4
4-Runner 2013
(without NAV)
TOOLS REQUIRED
• Cutting tool • Tape • Crimping tool
• Connectors (example: butt connectors, bell caps, etc.)
CAUTION!
Metra recommends disconnecting the negative battery terminal before beginning any instal -
lation, unless the vehicle manufacturer recommends against so. Please check with your local Dealership
for more information. All accessories, switches, climate controls panels, and especially air bag indicator
lights must be connected before reconnecting the battery or cycling the ignition. Also, do not remove the
factory radio with the key in the on position, or the vehicle running. It would be best to remove the key
from the ignition and then wait a few seconds before removing the factory radio.
axxessinterfaces.com • metraonline.com
Axxess Integrate
REV. 1/25/16 © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
FEATURES
2015-2016 Rav-4
(after build
2014-2016
date Nov. 2013)
2014-2016 Sienna
2014-2016 Sequoia
2015 Tacoma
2015 Tundra
2015-2016 Venza
Installation Instructions for AX-TOYCAM3
The AX-TOYCAM3 can be connected two different ways
To retain the factory back-up camera to an aftermarket radio:
• Connect the Black wire to chassis ground.
• Connect the Yellow wire to accessory power.
• Connect the male Yellow RCA jack to the rear camera input of the aftermarket radio.
• Connect the reverse wire from the aftermarket radio, to the reverse signal in the vehicle.
• Disregard the loose Green/Purple wire, it will not be used in this application.
To allow an aftermarket camera to be added to the OEM screen:
• Connect the Black wire to the ground wire of the aftermarket camera.
• Connect the Yellow wire to battery wire of the aftermarket camera.
• Connect the female Yellow RCA jack to the aftermarket camera.
2014
2015
The following (2) steps are only required if
2014-2016
a wire is not present in the factory harness.
2014-2016
*Except Avalon 2013-2014 and Venza 2013-2014
2014-2016
• If a wire is not present in pin-2 of the 28-
2015-2016
pin connector of the factory radio, unplug
the connector, then insert the metal pin
of the loose Green/Purple wire into it.
Connect the harness back into the radio.
• Connect the other end of the loose
Green/Purple wire to the reverse
wire of the vehicle.
Axxess Integrate
REV. 1/25/16
Connections to be made
14 13 12 11 10 9 8 7 6 5 4 3 2 1
28 27 26 25 24 23 22 21 20 19 18 17 16 15
This is the wire view of the connector in the vehicle
K P
NOWLEDGE IS OWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
axxessinterfaces.com • metraonline.com
© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
28 Pin Harness
Metra recommends MECP
certified technicians