Axxess AX-TOYCAM2-6V Instrucciones De Instalación

Installation Instructions for AX-TOYCAM2-6V
AX-TOYCAM2-6V
Toyota Back-Up Camera Retain/Add-On
2006-2013
INTERFACE FEATURES
• Retains the factory back-up camera to an aftermarket radio
• Allows an aftermarket camera to be added to the factory screen*
• Includes the AX-CAM6V 12-volt to 6-volt converter
* Display and navigation model radios only
INTERFACE COMPONENTS
• AX-TOYCAM2-6V harness • AX-CAM6V 12-volt to 6-volt converter
APPLICATIONS
TOYOTA
4-Runner 2012-2013
(with a factory amp)
4-Runner 2006-2011
Avalon 2011-2012
Camry 2007-2011
Highlander 2008-2012
TOOLS REQUIRED
• Cutting tool • Tape • Crimping tool
• Connectors (example: butt connectors, bell caps, etc.)
CAUTION!
All accessories, switches, climate controls panels, and especially air bag indicator lights
must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
® axxessinterfaces.com • metraonline.com
Axxess Integrate
REV. 10/10/16 © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
Prius 2010-2011
Sienna 2008-2010
Sequoia 2008-2012
(with a factory amp)
Tundra 2007-2013
(with a factory amp)
Venza 2009-2012
(with NAV)
Installation Instructions for AX-TOYCAM2-6V
Connections to be made
The AX-TOYCAM2-6V can be connected two different ways
To retain the factory backup camera to an aftermarket radio:
• Connect the Black wire to chassis ground and also to the Black wire of the AX-CAM6V.
• Connect the Yellow wire to the Blue/Red wire of the AX-CAM6V.
• Connect the reverse wire from the aftermarket radio, to the reverse signal in the vehicle,
and also to the Blue/White wire of the AX-CAM6V.
• Connect the male Yellow RCA jack to the rear camera input of the aftermarket radio.
• Disregard the loose Green/Purple wire, it will not be used in this application.
To allow an aftermarket camera to be added to the OEM screen:
• Connect the Black wire to the ground wire of the aftermarket camera.
• Connect the power wire of the aftermarket camera to accessory power.
• Tape off and disregard the Yellow wire, it will not be used in this application.
• Connect the female Yellow RCA jack to the aftermarket camera.
• The AX-CAM6V 12-volt to 6-volt converter will not be used in this application.
The following (2) steps are only required if a wire
is not present in the factory harness .
• If a wire is not present in pin-5 of the 5-pin
connector of the factory radio, unplug the
connector, and then insert the metal pin
of the loose Green/Purple wire into it.
Connect the harness back into the radio.
• Connect the other end of the loose Green/
Purple wire to the reverse wire of the vehicle .
K P
NOWLEDGE IS OWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
® axxessinterfaces.com • metraonline.com
Axxess Integrate
REV. 10/10/16 © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
5 Pin Harness
1 2 3 4 5
This is the wire view of the
connector in the vehicle
Metra recommends MECP
certified technicians