Protecting The Environment; Technical Data - Stanley FATMAX FMCD900 Manual De Instrucciones

Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Warning! Do not apply chisels when the tool is in the drilling
mode.
Switching on and off (fig. G)
To switch the tool on, press the on/off switch (1).
u
To switch the tool off, release the on/off switch.
u
Forward/reverse action (fig. H)
Move the selecter (2) to indicate the direction you require.
u
Selecting the operating mode (fig. I)
The tool can be used in three operating modes.
To operate the operating mode selector (3), push the
u
unlock button (21) and rotate the selector towards the
required position, as indicated by the symbols.
Drilling
For drilling in steel, wood and plastics, and for
u
screwdriving set the operating mode selector (3) to the
position (22).
Hammer drilling
For hammer drilling in masonry and concrete, set the
u
operating mode selector (3) to the
When hammering, the tool should not bounce and run
smoothly. If necessary, increase the speed.
Hammering
For hammering with spindle lock, and for light chiselling
u
and chipping, set the operating mode selector (3) to the
position (20).
When changing from hammer drilling to chiselling, turn the
u
chisel to the desired position. If resistance is felt during
mode change, slightly turn the chisel to engage the
spindle lock.
Accessories
The performance of your tool depends on the accessory used.
Stanley Fat Max accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your Stanley Fat Max corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.

Protecting the environment

Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according to
position (19).
local provisions. Further information is available at
www.2helpU.com

Technical data

Input voltage
No-load speed
Impact rate
Weight
Max. drilling capacity
Concrete
Steel
Wood
Battery
Voltage
Capacity
type
Charger
Input Voltage
Output Voltage
Current
(Original instructions)
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
FMCD900M2S
FMCD900M1S
FMCD900M2T
V 18
DC
min 0 - 2200
-1
min 0 - 5775
-1
kg 2.80
mm 20
mm 13
mm 30
FMC688L
V 18
DC
Ah 4.0
Li-Ion
906086**
typ. 1
V 230
AC
V 18
DC
A 2.0
ENGLISH
FMCD900B
18 18
0 - 2200 0 - 2200
0 - 5775 0 - 5775
2.80 2.15
20 20
13 13
30 30
FMC688L Not Supplied
18
4.0
Li-Ion
906086**
Not Supplied
typ. 1
230
18
2.0
7