Safety Information For Multi-Cutters - Berner BACOT 12V STARLOCK Manual Original

ures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of chil-
u
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous
in the hands of untrained users.
Maintain power tools and accessories. Check
u
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation. If
damaged, have the power tool repaired be-
fore use. Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean. Properly
u
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
Use the power tool, accessories and tool bits
u
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Keep handles and grasping surfaces dry,
u
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unex-
pected situations.
Battery tool use and care
Recharge only with the charger specified by
u
the manufacturer. A charger that is suitable
for one type of battery pack may create a risk of
fire when used with another battery pack.
Use power tools only with specifically desig-
u
nated battery packs. Use of any other battery
packs may create a risk of injury and fire.
When battery pack is not in use, keep it away
u
from other metal objects, like paper clips,
coins, keys, nails, screws or other small
metal objects, that can make a connection
from one terminal to another. Shorting the
battery terminals together may cause burns or a
fire.
Under abusive conditions, liquid may be ejec-
u
ted from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
Do not use a battery pack or tool that is dam-
u
aged or modified. Damaged or modified bat-
teries may exhibit unpredictable behaviour res-
ulting in fire, explosion or risk of injury.
Do not expose a battery pack or tool to fire or
u
excessive temperature. Exposure to fire or
temperature above 130 °C may cause explosion.
16 | English
English
Follow all charging instructions and do not
u
charge the battery pack or tool outside the
temperature range specified in the instruc-
tions. Charging improperly or at temperatures
outside the specified range may damage the
battery and increase the risk of fire.
Service
English
Have your power tool serviced by a qualified
u
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
Never service damaged battery packs. Ser-
u
vice of battery packs should only be performed
by the manufacturer or authorized service pro-
viders.

Safety information for multi-cutters

Hold power tool by insulated gripping sur-
u
faces, when performing an operation where
the cutting accessory may contact hidden
wiring. Cutting accessory contacting a "live"
wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
Use clamps or another practical way to se-
u
cure and support the workpiece to a stable
platform. Holding the workpiece by hand or
against your body leaves it unstable and may
lead to loss of control.
Only use the power tool for dry sanding. Wa-
u
ter entering a power tool will increase the risk
of electric shock.
Warning: Danger of fire! Avoid overheating
u
the workpiece and the sander. Always empty
the dust collector before taking a break from
work. Sanding dust in the dust bag, microfilter,
paper bag (or in the filter bag or vacuum
cleaner filter) can spontaneously combust un-
der certain conditions, for example if flying
sparks are created when sanding metals. This
risk is increased if the sanding dust is mixed
with paint or polyurethane residue or with other
chemical substances and if the workpiece is
hot as a result of prolonged work.
Keep hands away from the sawing area. Do
u
not reach under the workpiece. Contact with
the saw blade can lead to injuries.
Clean the air vents on your power tool regu-
u
larly. The motor's fan will draw the dust inside
the housing and excessive accumulation of
powdered metal may cause electrical hazards.
Use suitable detectors to determine if there
u
are hidden supply lines or contact the local
utility company for assistance. Contact with
electric cables can cause fire and electric
shock. Damaging gas lines can lead to explo-
English
1 609 92A 4RW • 17.12.18