3M MT15H7-WS6 Serie Manual De Instrucciones página 9

EN
3M™ PELTOR™ WS™ ProTac XPI Headset
MT15H7*WS6*
INTRODUCTION
Congratulations and thank you for choosing 3M™
PELTOR™ hearing protection solutions!
3M™ PELTOR™ WS™ ProTac XPI Hearing protection
has built-in Bluetooth technology and a level-dependent
®
function for ambient listening. Welcome to the next
generation of protective communication.
IMPORTANT
Please read, understand, and follow all safety information
in these instructions prior to use. Retain these
instructions for future reference. For additional
information or any questions, contact 3M Technical
Services (contact information listed on the last page).
INTENDED USE
These 3M™ PELTOR™ headsets are intended to provide
workers with protection against hazardous noise levels
while allowing the user to communicate via built-in
Bluetooth technology or other audio devices and hear
®
the surroundings via the ambient microphones. It is
expected that all users read and understand the provided
user instructions as well as be familiar with the use of this
device.
!
WARNING
This hearing protector helps reduce exposure to hazardous
noise and other loud sounds. Misuse or failure to wear
hearing protection at all times when exposed to hazardous
noise may result in hearing loss or injury. For correct use,
consult supervisor and User Instructions, or call 3M Technical
Services. If your hearing seems dulled or you hear a ringing
or buzzing during or after any noise exposure (including
gunfire), or for any other reason you suspect a hearing
problem, leave the noisy environment immediately and
consult a medical professional and/or your supervisor.
Failure to follow these instructions may result in serious
injury or death:
a. Listening to audio communication may reduce your
situational awareness and ability to hear warning signals.
Stay alert and adjust the audio volume to the lowest
acceptable level. The audibility of warning signals at a specific
workplace may be impaired while using the entertainment
facility.
b. To reduce the risks associated with igniting an
explosion, do not use this product in a potentially explosive
atmosphere.
Failure to follow these instructions may reduce the
protection provided by the earmuff and may result in
hearing loss:
a. Research suggests that users may receive less noise
reduction than indicated by the attenuation value(s) on the
packaging, due to variation in fit, fitting skill, and motivation
of the user. Refer to your applicable regulations for guidance
on how to adjust label values and estimate attenuation. In
addition, 3M strongly recommends fit testing of hearing
protectors.
b. 3M strongly recommends individual fit testing of hearing
protectors. If the NRR or SNR is used to estimate typical
workplace protection, 3M recommends that the noise
reduction value be reduced by 50% or in accordance with
applicable regulations.
c. Ensure the hearing protector is properly selected, fit,
adjusted, and maintained. Improper fit of this device will
reduce its effectiveness in attenuating noise. Consult the
enclosed instructions for proper fit.
d. Inspect the hearing protector before each use. If
damaged, select an undamaged hearing protector or avoid
the noisy environment.
e. When additional personal protective equipment is
necessary (e.g. safety glasses, respirators, etc.), select
flexible, low profile temples or straps to minimize interference
with the earmuff cushion. Remove all other unnecessary
articles (e.g. hair, hats, jewelry, headphones, hygiene covers,
etc.) that could interfere with the seal of the earmuff cushion
and reduce the protection of the earmuff.
f. Do not bend or reshape the headband or neckband, and
ensure there is adequate force to hold the earmuffs firmly in
place.
g. Earmuffs, and in particular cushions, may deteriorate with
use and should be examined at frequent intervals for
cracking and leakage, for example. When used regularly,
replace the ear cushions and foam liners at least twice a
year to maintain consistent protection, hygiene, and comfort.
h. The output of the electrical audio circuit of this hearing
protector may exceed the daily limit sound level. Adjust the
audio volume to the lowest acceptable level.
i. If the requirements above are not adhered to, the
protection afforded by the earmuffs will be severely impaired.
EN 352 Safety Statements:
The output of the level-dependent circuit of this hearing
protector may exceed the external sound level.
• The fitting of hygiene covers to the cushions may affect the
acoustic performance of the earmuffs.
• Performance may deteriorate with battery usage. The
typical period of continuous use that can be expected from
the earmuff battery is approximately 40 hours.
• This product may be adversely affected by certain chemical
substances. Further information should be sought from the
manufacturer.
• These helmet mounted earmuffs are of "large size range".
Helmet mounted earmuffs complying with EN 352-3 are of
"medium size range" or "small size range" or "large size
range". "Medium size range" helmet mounted earmuffs are
designed to fit the majority of wearers. "Small size range" or
"large size range" helmet mounted earmuffs are designed to
fit wearers for whom "medium size range" helmet mounted
earmuffs are not suitable.
1