Rimage Professional 3400 Guia De Instalacion página 2

8
Remove the ribbon carriers
Note: For more detailed instructions on replacing print and

retransfer ribbons, refer to the Rimage Professional 3400 and
5400N User Guide.
- Important! Do not attempt to remove the ribbon carriers from the
printer unless the system is powered on.
a. Turn the center latch counterclockewise to unlock it.
b. Pull the print ribbon carrier or retransfer ribbon carrier to remove it
from the printer.
Print Ribbon Carrier
Unlocked
9
Install or replace the print ribbons
a. Lay the print ribbon carrier on its back.
Print Ribbon Carrier
b. Remove the used print ribbon (if needed).
i. Pull up on supply roll and takeup roll.
ii. Remove the ribbon from the carrier.
c. Install the new print ribbon.
i. With the supply roll on the right side,
and the takeup roll on the left side,
unroll a few inches of ribbon.
ii. Place the print ribbon carrier on top
of the exposed ribbon.
iii. Place the supply roll on the carrier
and push down to snap it into place.
iv. Place the takeup roll on the carrier and
push down to snap it into place.
v. Lay the print ribbon carrier back on its side.
d. Return the print ribbon carrier to the printer.
e. Turn the center latch clockwise to secure it.
f. Close the printer cover.
2001432_B_EN
10
Install or replace the retransfer ribbon
a. Remove the retransfer ribbon carrier
from the autoloader.
b. On first use, remove the packaging from
the retransfer ribbon carrier.
i.
ii. Remove tape and
Retransfer Ribbon
Carrier
Center Latch
Locked
c. Remove the used retransfer ribbon
from the retransfer ribbon carrier
(if needed).
i.
ii. Remove the ribbon from the
d. Install the new retransfer ribbon.
Supply Roll
Takeup Roll i.
ii. Place the retransfer ribbon
Supply Roll
iii. Place the supply roll on the carrier
Takeup Roll
iv. Place the takeup roll on the carrier
e. Return the retransfer ribbon carrier to the autoloader.
f. Turn the center latch clockwise to secure the carrier.
g. Close the printer cover.
Remove the tape
and plastic brace
from the front of the
carrier.
Tape and
plastic packaging
Plastic Brace
from around the
outside of the
carrier.
Supply Roll
Pull up on the supply roll and
the takeup roll.
carrier.
With the supply roll on the left
Supply Roll
side, and the takeup roll on the
right side, unroll a few inches
of ribbon.
carrier on top of the exposed
ribbon.
and push down to snap it into place.
and push down to snap it into place.
Copyright © 2010 Rimage Corporation
11
Test and verify
Use Rimage QuickDisc to run a 3-disc test job to verify that the system
is operating correctly. Refer to the Getting Started with Rimage
Software document included on the Rimage Professional 3400/5400N
User Guide disc.
Tape and
Plastic
Packaging
12
Register the Rimage system
-
Important! Make sure to register your system so that Rimage can
notify you of upgrades as they become available.
Product registration and warranty activation is available at
www.rimage.com/support/warranty-registration.
Takeup Roll
13
Learn more
These documents are available on the Rimage Professional
•
3400/5400N User Guide Disc that shipped with your autoloader:
Rimage Professional 3400 and 5400N User Guide
ƒ
Getting Started with Your Rimage Software
ƒ
Rimage Advanced Setup (Networking) Guide
ƒ
Diagnostic Test Instructions
ƒ
Takeup Roll
Access these documents by placing the User Guide disc in the
disc drive of a PC.
 Note: If the User Guide menu does not display automatically,
select Run from the Windows Start menu and browse to the
Home.htm file on the software disc.
For information about operating and maintaining the 3400, refer
•
to the Rimage Professional 3400 and 5400N User Guide.
For additional support and product information, go to
•
www.rimage.com/support.
Page 2