Troubleshooting - Broil King Imperial XLS Manual Del Usuario

TROUBLESHOOTING

PROBLEM
SMELL OF GAS
Leak detected at any connection.
Flames Beneath Control Panel
(Flashback Fire)
Burner Not Lighting
Ignitor Not Working
Decreasing Heat, "Popping
Sound"
Hot spots on Cooking Surface
"Flare-ups" or Grease Fires
Yellow Flame
Inside of Lid Appears to be
Peeling
Cooking Grids Rusting
Control panel or oven lights not
working
If troubleshooting fails to solve any of these or any other issues, please visit www.omcbbq.com for more information including troubleshooting
videos, tricks and tips or call customer service at 1-800-265-2150
POSSIBLE CAUSE
SHUT OFF GAS SUPPLY AT ONCE.
DO NOT USE THE APPLIANCE UNTIL LEAK IS SEALED.
1. Quick disconnect coupling not seated fully.
2. Gas leak in connection.
3. Gas leak in hose or control valves
1. Venturi blocked.
1. Gas shut off valve closed.
2. Ignitor issue.
3. Venturi blocked or misaligned with valve orifice.
4. Orifice(s) blocked.
5. Hose is twisted.
1. Ignitor battery is dead
2. Ignitor wire(s) not connected
3. Electrode misaligned on burner
4. Ignitor malfunction
1. Venturi blocked.
1. Venturi blocked
2. Debris buildup on Flav-R-Wave
1. Excessive grease buildup on vaporizer or in gas grill
cook box
2. Excessive heat.
1. Some yellow flame is normal. If it is excessive, the
venturi may be blocked.
2. Burner ports blocked.
1. This is a build-up of grease. The inside of lid is not
painted and cannot peel.
1. Porcelain enamel has been chipped
1. Unit not connected to power.
2. Faulty transformer.
3. Loose or corroded connections.
4. Bulb blown
CORRECTIVE ACTION
1. Remove and reconnect coupling
2. Tighten connection and "Leak Test".
3. See authorized service centre
1. Remove burner and clean venturi. See "Venturi Tubes"
(page 4)
1. Open gas shut off valve.
2. Try manually lighting burner with a match. See "Lighting"
(page 6). If burner lights successfully, it is an ignitor issue.
See "Ignitor not Working" below
3. Remove burner, clean venturi and realign with valve
orifice. See page 4 for assistance.
4. Remove burner, clean orifices with a pin or fine wire. Do
not drill orifices.
5. Straighten hose. Keep away from bottom casting.
1. Replace battery
2. Ensure main burner and side burner electrode wires are all
connected
3. Realign electrode and clear any surrounding debris from
area
4. Use "Match Lighting" procedure. (Page 6)
2. Remove burner, clean venturi. See "Venturi Tubes"
(Page 4) for assistance.
1. Remove burner, clean venturi. See "Venturi Tubes"
(page 4) for assistance.
2. Scrape off Flav-R-Wave and vacuum
1. Thoroughly scrape off Flav-R-Wave and inside of cookbox
then vacuum out debris
2. Turn burner controls to a lower setting
1. Remove burner, clean venturi. See "Venturi Tubes"
(page 4) for assistance.
2. Remove burner & clean with soft bristle brush (e.g.
toothbrush).
1. Clean with stiff bristle brush or scraper.
1. See "Maintenance" (page 10) for help
1. Connect GFI power cord to appliance. Plug to working
power outlet.
2. Check transformer output is 12Vac. Replace if required.
3. Clean connections and ensure all connectors are pushed
together firmly.
4. Replace bulbs.
11