Chicco STROLL'IN'2 Manual Del Usuario página 14

Ocultar thumbs Ver también para STROLL'IN'2:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 24
• 2 rear wheels
• Rear axle
• Rear wheel installation kit (2 washers, 2 spring pins, 2 plugs)
• Bumper bar/children's tray
• Hoods
• Comfort kit (padded shoulder and crotch straps)
• Carry-all bag
• Rain cover
TIPS FOR CLEANING AND MAINTENANCE
WARNING: This product requires regular periodical maintenance.
The cleaning and maintenance of the product must only be
carried out by an adult.
CLEANING
Clean the fabric parts using a wet sponge and neutral soap.
The lining can be removed (please refer to the section "Fitting/
removing the seat lining"). Please refer to the care labels for
instructions on how to clean the fabric parts. Below are the
cleaning symbols and their meanings:
Wash by hand with cold water.
30° C
Do not bleach
C
Do not tumble dry
Do not iron
Do not dry clean
Routinely wipe clean plastic parts with a soft damp cloth. Never
use solvents or abrasive detergents. Always dry the metal parts
to prevent the formation of rust if the stroller has come into
contact with water.
MAINTENANCE
If necessary, lubricate the moving parts with dry silicone lubri-
cant. Regularly check the condition of the wheels and clean
off all dust and sand. To avoid friction that may compromise
the correct functioning of the stroller, make sure that all plastic
parts that slide on the metal tubes are free of dust, dirt and
sand. Keep the stroller in a dry place.
OPENING AND FIRST ASSEMBLY
1. Completely open the stroller frame (Fig. 1A-1B) until you
hear a click.
2. Insert the front wheel pins in the dedicated slots on the frame
(Fig. 2). Repeat the operation for the other front wheel.
WARNING: Before using, ensure that the wheels are correctly
attached by pulling them downwards.
3. To assemble the wheels on the rear axle, fit the following
parts in the correct order, see Fig. 3:
• wheel (A)
• washer (B)
• spring pin (C)
• plug (D)
Make sure you insert the fastening spring pin as indicated in the
diagram: the straight side must be inserted in the hole in the
pin. Repeat this operation also for the other wheel, following
the same sequence.
4. Fit the rear axle with the wheels mounted in the relevant
slots in the frame until you hear it click into place (Fig. 4).
WARNING: Before using ensure that the wheels and rear axle
are correctly attached.
5. To complete assembly attach the platform to the rear axle
(Fig. 5A-5B). When concluded, the platform will be assembled
as in Figure 5C.
6. To fit the hood, fasten the plastic clips to the frame's tubes
matching the holes in the clips with the pins on the tubes
(Fig. 6A-6B). To remove the hood, turn the fastening clips
outwards (Fig. 6C).
7. Insert the bumper bar/children's tray in the dedicated slots
until they click into place (Fig. 7A). To remove the bumper bar/
children's tray press the two side buttons and pull towards
you (Fig. 7B).
WARNING: Never use the bumper bar/children's tray to lift the
stroller with your child sitting in it.
SAFETY HARNESS
On the front seat the stroller has a five-point safety harness which
consists of two shoulder straps, a waist strap and a crotch strap
with buckle. The rear seat has a three-point safety harness which
consists of a waist strap and a crotch strap with buckle.
8. Make sure the shoulder straps are at a suitable height for
your child: adjust if necessary (Fig. 8).
9. After placing your child in the front seat, insert the two forks
in the buckle (Fig. 9A) and adjust the waist belt if necessary
by pressing the buttons at the side of the buckle. To unfasten
the waist belt press the central button (Fig. 9B).
10. After placing the second child in the rear seat, adjust the
waist belt by pressing the buttons at the side of the buck-
le (Fig. 10A). To unfasten the waist belt press the central
button (Fig. 10B).
WARNING: The use of the crotch strap, waist strap and safety
harness is necessary to guarantee the safety of your child.
WARNING: After removing the safety harness (e.g. to wash it),
ensure that the harness is reassembled correctly using the
anchorage points. The harness must be re adjusted.
HOW TO ADJUST THE BACKREST
11. The backrest can be adjusted into two positions using the
lever at the rear. To lower the backrest pull the lever up and
push the backrest back (Fig. 11). Vice versa, to straighten the
backrest lift the lever or push it forwards.
WARNING: These operations may be more difficult if your child
is sitting in the chair.
REAR BRAKES
The rear wheels have linked brakes, which can be applied
simultaneously on both rear wheels using one pedal only.
12. To apply the brakes, press one of the two pedals at the sides
of the rear wheels down, as shown in Figure 12.
13. To release the brakes, push up one of the two pedals to the
sides of the rear wheels, as shown in Figure 13.
SUN CANOPY
WARNING: The canopy must be fixed to both sides of the
stroller. Ensure that the canopy is correctly secured (see point 6).
14. To open the canopy, push the front arch forward (Fig. 14).
15. For greater protection from the sun's rays it is possible to
increase the fabric surface of the canopy by extending the
wings and the central fabric segment folded under the
canopy (Fig. 15A-15B).
CLOSING THE STROLLER
WARNING: When opening the stroller, make sure that your child
or other children are at a safe distance. Make sure that during
these operations the moving parts of the stroller do not come
into contact with your child. Before closing the stroller, make
sure that the storage basket is empty and the canopy is closed.
The stroller has a closing device that can be used with one hand.
16. To close the stroller push cursor "A" on the closing device (Fig.
16A) outwards and lift the tube at the same time (Fig. 16B).
17. When closed, the stroller stands up on its own (Fig. 17).
FITTING AND REMOVING THE STROLLER LINING
18. To remove the lining from the front seat lower the backrest
completely by pulling the lever and pushing it forwards
(Fig. 18A), remove the three plastic side wings (left and
right) from the backrest structure (Fig. 18B) and remove the
lining from the top edge of the backrest (Fig. 18C). Undo
14
19.
To
ord
thr
IN
Th
WA
to
20
WA
sea
21.
RE
At
a s
wh
22
WA
to
ch
the
RA
23
WA
a h
WA
lea
tem
WA
Th
no
for
da
Fo
ref
the

Publicidad

Tabla de contenido
loading

Tabla de contenido