Cleaning And Maintenance - Asist AE3KT14 Instrucciones De Uso

Ocultar thumbs

Contenido

página de 62

/ 62
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

the recesses (4).

Assembly / disassembly

Grinding table disassembly:

Use the supplied wrench (17) to loosen the screw (9)

under the grinding table (11). Remove the screw (9)

and washer (8) and pull off the grinding wheel holder

(10)

from the device.

Grinding table assembly:

To mount the sanding table (11), slide the sanding

table holder (10) back onto the device. Insert the

screw (9) with the washer (8) and retighten. Make

sure that the protrusions are in the correct position,

otherwise it will not be possible to screw in the screw

(9).

Replacing sandpaper

Caution, risk of injury!

Disconnect the device from the power supply to

prevent accidental switching on.

For easier replacement, first remove the sanding

table (11) and the holder (10)

Sanding paper assembly:

Press the sanding sheet (18) evenly on the sanding

disc (1).

Sanding sheet disassembly:

Remove the sanding sheet (18) from the grinding

wheel (1).

Test run:

After each sanding paper change, perform a no-load

test run for at least one minute without load and at

maximum speed. Do not stand in the danger area.

Grinding table angle adjustment

The angle of the sanding table (11) can be infinitely

adjusted between -10 ° and + 50 °.

Loosen the screws (7). Use the nut and angle scale

(6) to set the desired angle.

Tighten the screws again.

Using an angle stop

Loosen the angle stop bolts (20). Slide the angle stop

rails (19) to the desired position in the groove (12) on

the sanding table (11). Use the scale to set the requi-

red angle for the marking on the rail (19). Secure the

angle stop (13) by retightening the screw (20).

Dust extraction connection

Insert the angle adapter (14) into the hole on the

device.

Make sure that the protrusion on the angle adapter

(14) slides into a groove in the hole on the device.

Rotate the angle adapter (14) to a vertical or horizon-

tal position around the angle adapter (14) to secure it

from falling out.

Dust extraction removal:

Turn and gently pull on the angle adapter (14) and

remove it. The adapter can be removed while fitting

an arrow on the angle adapter (14) and a mark on the

cover of the device. An additional adapter (15) with a

larger diameter is supplied with the device, which can

optionally be mounted on an angled one

adapter (14). You can use an angle adapter

Alternatively, connect the suction hose of the vacuum

cleaner directly.

Switching on and off

Connect the device to the mains. Use the speed

control (2) to select the required speed.

Turn the switch to position „I" (3). The device starts

up.

Turn the switch to the „O" position (3). The device

switches off.

Then unplug the power cord (5).

After switching on, wait until the device reaches the

maximum speed. Only then start grinding.

Grinding

The arrow above the grinding wheel indicates the

direction of rotation of the disc grinder. The grinding

speed can be regulated using the speed controller

(2), switch on the grinder.

Allow the grinder to reach full speed and run without

load for one minute.

While holding the workpiece firmly, hold the surface

grind against the sanding sheet.

Note: Move it back and forth evenly on the sanding

disc to ensure even wear and extend the life of the

sanding paper.

Grinding tips

Never use force on the grinder. The weight of the

grinder adds sufficient pressure. Excessive pressure

slows down the motor, the sandpaper wears out

quickly, and the speed of the sander is significantly

reduced. This slows down the grinding speed and

creates a lower quality surface.

Check your workpiece frequently. The grinder is able

to quickly remove material, especially with rough

paper.

Do not grind in one place for too long. The quick

action of the grinder can remove too much material

and create an uneven surface.