Intended Use; Belt Sander Safety Warnings; General Working Stand Safety Warnings - Ryobi R18BS Traducción De Las Instrucciones Originales

Safety, performance, and dependability have been given
top priority in the design of your belt sander.

INTENDED USE

This belt sander is intended for sanding metal, wood,
plastic, or similar materials. It can also remove paint,
varnish, and corrosion from surfaces.
It is intended to be used by operators who have read the
instruction manual and understand the risks and hazards.
Belt sanders should only be used in well ventilated areas.
This belt sander is designed for dry sanding only. Do not
use for wet sanding.
The product is intended for consumer use only. Do not use
the belt sander in any way other than those stated in the
intended use.
WARNING
Dust from certain paints, coatings, and materials may
cause irritation or allergic reactions to the respiratory
system. Dust from wood, such as oak, beech, MDF, and
others are carcinogenic. Materials containing asbestos
should only be worked or processed by quali ed
specialist operators.
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, re and/or serious injury.
Save all warnings and instruction for future reference.

GENERAL WORKING STAND SAFETY WARNINGS

WARNING
Read all safety warnings and all instructions
provided with the working stand and the power
tool to be mounted. Failure to follow the warnings
and instructions may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments or changing accessories.
Accidental starting of the power tool is a cause of some
accidents.
Properly assemble the working stand before
mounting the tool. Proper assembly is important to
prevent risk of collapse.
Securely fasten the power tool to the working stand
before use. Power tool shifting on the working stand
can cause loss of control.
Place the working stand on a solid, flat and level
surface. When the working stand can shift or rock, the
power tool or workpiece cannot be steadily and safely
controlled.
Do not overload the working stand or use as ladder
or scaffolding. Overloading or standing on the working
stand causes the stand to be "top-heavy" and likely to
tip over.

BELT SANDER SAFETY WARNINGS

Always wear safety goggles and a dust mask.
A suitable breathing respirator must be worn while
sanding lead paint, some woods and metal to avoid
breathing the harmful/toxic dust or air.
The product is not suitable for wet sanding.
Do not use sanding belt larger than needed.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
To reduce the risk of re, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in uid or allow a uid to
ow inside them. Corrosive or conductive uids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
Entrapment/contact with the moving belt
Additional caution must be exercised, especially during
inverted operation, to prevent operator's fingers and
hands from coming into contact with the abrasive belt
or entrapped by the rollers.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
English | 1