Service Information; Disposal And Recycling - Scheppach 5906102901 Traducción Del Manual De Instrucciones Origina

Turn the perforated exhaust nut (17.1) counterclock-
wise to open it and use your hands to pull the valve rod
outwards over the perforated exhaust nut (17.1) to open
the safety valve outlet. Now, the valve audibly releases
air. Then, tighten the exhaust nut clockwise again.
10.4 Checking the oil level at regular intervals
(Fig. 11)
Place the compressor on a level and straight surface.
The oil level must be between the MAX and MIN marks
on the oil level window (12).
Oil change: we recommend SAE 15W 40 or equiva-
lent.
The original oil filling must be changed after 10 hours
in operation; thereafter the oil must be drained and re-
placed with new oil after every 50 hours in operation.
10.5 Changing the oil (Fig. 1, 10, 11)
Switch off the engine and pull the mains plug out of the
socket. Remove the oil sealing plug (15). After releas-
ing any air pressure you can unscrew the oil drain plug
(12) from the compressor pump (13).
To prevent the oil from running out in an uncontrolled
manner, hold a small metal chute under the opening
and collect the oil in a vessel. If the oil does not drain
out completely, we recommend tilting the compressor
slightly. When the oil has drained out, re-fit the oil drain
plug (12). Dispose of the old oil at a drop-off point for
old oil. To fill in the correct quantity of oil, make sure
that the compressor stands on an even surface. Fill
new oil through the oil filler opening (19) until it comes
up to the maximum level. This is marked with a red dot
on the oil level window (12) (Fig. 11). Do not exceed
the maximum filling quantity. Overfilling the equipment
may result in damage. Reinsert the oil sealing plug (15)
into the oil filler opening (19).
10.6 Cleaning the intake filter (Fig. 3, 12, 13)
The intake filter prevents dust and dirt being drawn in.
It is essential to clean this filter after at least every 300
hours in service. A clogged intake filter will decrease
the compressor's performance dramatically. Open the
screw (E) to remove the intake filter (2x).
Then pull off the filter cover (D). Now you can remove
the air filter (F). Carefully tap out the air filter, filter cov-
er and filter housing. Then blow out these parts with
compressed air (approx. 3 bar) and reinstall in reverse
order.
28 | GB
10.7 Storage
m Important!
Pull out the mains plug and ventilate the equip-
ment and all connected pneumatic tools. Switch
off the compressor and make sure that it is se-
cured in such a way that it cannot be started up
again by any unauthorized person.
m Important!
Store the compressor only in a dry location which
is not accessible to unauthorized persons. Always
store upright, never tilted! Oil may leak out!
10.7.1 Releasing excess pressure
Release the excess pressure by switching off the com-
pressor and using the compressed air which is still left
in the pressure vessel, e.g. with a compressed air tool
running in idle mode or with a blow-out pistol.

10.8 Service information

Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consum-
ables.
Wear parts*: belt, coupling
* Not necessarily included in the scope of delivery!
Spare parts and accessories can be obtained from our
service centre. To do this, scan the QR code on the
cover page.

11. Disposal and recycling

The unit is supplied in packaging to prevent
its being damaged in transit. This packaging
is raw material and can therefore be reused
or can be returned to the raw material system.
The unit and its accessories are made of var-
ious types of material, such as metal and plas-
tic. Defective components must be disposed of as spe-
cial waste. Ask your dealer or your local council.
www.scheppach.com