Diagrama De Cableado; Piezas De Repuesto; Descripción; Congelación) - Pentair INTELLICONNECT Manual De Instalación

Diagrama de cableado

IMPORTANTE: ambos cables (patas) de la conexión eléctrica deben pasar a través del relé para que el equipo conectado
funcione correctamente. Si solo un cable (pata) se rompe, el circuito no podrá detectar con precisión el amperaje del mismo.
La detección de amperaje mínimo se utiliza para permitir que IntelliConnect encienda de manera segura el calentador o el clorador
de sal. Esto también se utiliza para determinar si el equipo de relé está encendido o no.
Los generadores IntelliChlor/iChlor, las bombas IntelliFlo y los calentadores deberían recibir corriente directamente del disyuntor
(para recibir corriente constante) y no deberían estar conectados a través del relé 1 o del relé 2.
When this enclosure is installed
correctly, the arrow to the left will
be pointing up towards the wiring
compartments.
The enclosure MUST be installed so that the
conduit holes are on the bottom side of the
enclosure. This allows for proper drainage and
prevents damage to internal electrical
components.
CONTROL BOARD RATINGS
Input: 100-240 V, 100 mA, 50/60 Hz
RELAY CONTACT RATINGS (60 Hz)
General: 20 A, 277 V
PUMP
1 HP, 120 V 1 kW, 120 V TUNGSTEN
2 HP, 240 V 1.3 kW, 240 V TUNGSTEN
16 FLA/96 LRA, 120 V 10 A, 240 V BALLAST
15 FLA/90 LRA, 240 V
Note: This equipment is not provided with integral Ground Fault Circuit Interruptors (GFCI)
protection.
Note: When this equipment is used to power or switch an underwater luminaire, suitable GFCI
protection shall be provided in the field. Luminaire circuit conductors shall not occupy conduit,
boxes or enclosures with other circuits unless the other circuits are also GFCI protected.
Note: This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.

Piezas de repuesto

CONTAINS - FCC ID: 2AC7Z-ESPWROOM32, IC: 21098-ESPWROOM32
P/N Descripción
READ AND UNDERSTAND ALL
WARNING AND SAFETY
523327 Kit de repuesto de placa de control IntelliConnect
INSTRUCTIONS BEFORE SERVICING
OR OPERATING THIS EQUIPMENT.
LIGHT HEATER
0.5 A, 24 V
INTELLICONNECT CIRCUIT BOARD
P2 P1
RS-485
CONNECTIONS
WATER TEMP.
SENSOR
HEATER
CONNECTIONS
MINIMUM 25 CUBIC INCHES IN WIRING COMPARTMENT
MAINTAIN ALL GROUND CONNECTIONS IN WIRING
COMPARTMENT.
USE MINIMUM 75˚C COPPER CONDUCTORS ONLY.
NEMA 4X, CSA TYPE 3 "RAINPROOF" ENCLOSURE. SUITABLE
FOR INDOOR OR OUTDOOR USE. SUITABLE FOR SWIMMING
POOL/SPA APPLICATIONS.
Manual de instalación del sistema de control y monitoreo IntelliConnect
DATOS TÉCNICOS
RELAY 1
P4
LINE 1
LINE 2 / NEUTRAL
LINE 1 (IN)
LOAD 1 (OUT)
LINE 2 (IN)
LOAD 2 (OUT)
LINE 1 (IN)
LOAD 1 (OUT)
LINE 2 (IN)
LOAD 2 (OUT)
P/N 523336 Rev. B 9/6/18
9
RELAY 2