Safety And Control Devices; Disposal Of Packaging And The Appliance; Instructions For Installation; Reminders For The Installer - AFG NI74TED Instrucciones Para Instalación, Uso Y Mantenimiento

• Do not wash the body or flame spreader of the hob burners
in the dishwasher.

3 SAFETY AND CONTROL DEVICES

4 DISPOSAL OF PACKAGING AND THE APPLIANCE

PACKAGING
The packaging is made using environmentally friendly mate-
rials. The plastic recyclable components are:
• the transparent cover, the bags containing the instructions
manual and nozzles ( made of polyethylene - PE.).
• the straps (in polypropylene - PP).
APPLIANCE
The appliance is manufactured 90% from recyclable metals
(stainless steel, aluminum sheet, copper.... ).
The appliance must be scrapped in compliance with current
regulations governing such disposal.
• It must be disposed of properly.
• Make the appliance unusable before scrapping.
5 RISKS DUE TO NOISE
• As regards airborne acoustical noise emissions, the A-
weighted sound pressure level is below 70 dB(A).

INSTRUCTIONS FOR INSTALLATION

REMINDERS FOR THE INSTALLER

The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules.
• Read this manual carefully. It provides important information
for safe installation, use and maintenance of the appliance.
• Installation, conversion to a different type of gas and applian-
ce maintenance must be carried out by qualified technicians
authorized by the manufacturer, in compliance with current
safety standards and the instructions given in this manual.
• Identify the specific appliance model. The model number is
detailed on the packaging and on the appliance data plate.
• The appliance must be installed in a well-ventilated room.
• Do not obstruct any air vents or drains present on the ap-
pliance.
• Do not tamper with appliance components.

6 REFERENCE STANDARDS AND LAWS

Install the appliance in compliance with current safety regula-
tions.
Install the appliance in compliance with current regulations.

7 HANDLING

The packaging is marked with warning symbols that indicate
the precautions to be taken when handling the appliance to
avoid damage.The appliance must only be handledusing su-
itable equipment. If lifting equipment is used, such as forklift
trucks or similar, make sure that the appliance is in a stable
position.

8 UNPACKING

Check the state of the packaging and in the event of damage,
ask the delivery person to inspect the goods.
• Remove the packaging.
• Remove the protective film from the exterior and interior pa-
nels. Use a suitable solvent to remove any residual adhesive
from the panels.

9 POSITIONING

• The overall dimensions of the appliance and the position of
connections are given on the installation diagram at the start
of this manual.

10 FUMES EXHAUST SYSTEM

11 CONNECTIONS

The position and dimensions of connections are given in the
installation diagram at the start of this manual.
ELECTRICAL CONNECTIONS
Check that the appliance is designed to operate at the voltage
and frequency of the power supply present on site. Check the
details given on the appliance data plate.
The meaning of symbol
ROUS VOLTAGE.
• Install an adequately rated omnipolar circuit-breaker upline
of the appliance in an easily accessible point, in compliance
with installation regulations; the circuit breaker must guaran-
tee immediate omnipolar disconnection from the mains, with
a minimum contact opening that allows complete disconnec-
tion in overvoltage category III conditions.
• Installupline of the applianceacircuit breakerof the type indi-
catedintableT6.
• Installupline of the appliancea Residual Current Device
(RCD) dimensioned for minimum current of 30mA. It is re-
commended to use a short-time delay AC-DC sensitive resi-
dual current protective device.
• For electrical connection, use a rubber-sheathed flexible ca-
ble which is oil resistant, type H05RN-F or H07RN-F, for ca-
ble size consult the technical data table.
• Connect the power supply cable to the terminal board as
shown in the wiring diagram supplied with the appliance.
• Secure the power supply cable with the cable clamp.
• Protect the power supply cable on the outside of the applian-
ce with a rigid plastic or metal pipe.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
PROTECTIVE EARTH AND EARTH BONDING CONNEC-
TIONS
Connect the appliance to an efficient ground circuit. Connect
the earth conductor to the terminal with the symbol
ted next to the main terminal board.
Connect the metal structure of the appliance to the equipoten-
tial node. Connect the conductor to the terminal with the symbol
on the outside part of the bottom.
• This symbol indicates that the appliance must be included in
an equipotential system connected in compliance with cur-
rent regulations.
CONNECTION TO THE WATER SUPPLY
The appliance must be connected to a potable water supply.
• Install a mechanical filter and a shut-off valve upstream of the
appliance in an easily accessible point.
, if used, is: WARNING DANGE-
loca-
5