DeWalt DCR029 Traducido De Las Instrucciones Originales página 26

EngLIsh
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Inserting and Removing the Battery Pack
from the Radio (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Radio
1. Align the battery pack 17
receptacle 20 .
2. Slide it into the receptacle until the battery pack is firmly
seated in the tool and ensure that you hear the lock snap
into place.
To Remove the Battery Pack from the Radio
1. Press the release button 18
out of the battery receptacle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 19 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Powering with the AC Adapter (Fig. B)

WARNING: Use only the AC adapter supplied with
this product. Use of any other external power supply
could damage the radio or power supply.
To power the radio using the AC adapter
into the radio's AC power input
radio, then plug the 230V AC cord end into the wall outlet or
an appropriate-sized extension cord that is plugged into a wall
outlet. Always fully extend the cord before each use.
24
is fully charged.
17
with the rails inside the battery
and firmly pull the battery pack
, plug the cord
15
16 found on the back of the
To prevent interference, locate the adapter as far from the radio
as possible.
nOTE: The battery pack must be removed before the AC
adapter can be plugged into the AC power input.
Power/Volume Adjustment
1. To turn the radio on, press the ON/OFF button/Volume
knob .
1
nOTE: When the radio is first used it will enter 'DAB' mode
and automatically scan for stations. It will then start playing
the first station it finds.
2. Turn the ON/OFF button/Volume knob
to increase the volume. To decrease the volume, turn
anti-clockwise.
Mode Function
To choose one of the mode functions ('DAB', 'FM', or 'AUX' or
Bluetooth®) push the mode button
is found.
nOTE: Pressing the Bluetooth® button
into Bluetooth® mode.
DAB Mode
Tuning
When the unit is first switched on the unit will start in
'DAB'/'DAB+' mode and will 'Auto Scan' to find broadcast
stations in the local area. Once 'Auto Scan' is complete, use the
left or right arrow buttons to scroll through the stations.
3
nOTE: When moving locations or if reception was poor
in the original scan (possible if the antenna was not up),
this may result in an empty or incomplete list of available
stations. Manually running an 'Auto Scan' will find all available
broadcast stations.
To Perform an auto scan:
1. Press the Menu button 7 , scroll through the options
by pressing the right arrow button
'Auto Scan'.
2. Press the Enter/Display button
'Auto Scan'.
Once 'Auto Scan' is complete the radio will play the first station
it finds.
Display
Press the Enter/Display Button
scrolling text, date and station information.
station Prune
Some stations once received by your radio which are no longer
available may display with a ? after the station name.
To remove these stations from the station list, use the
'Prune' function:
1. Press Menu 7 and scroll right to the 'Prune' option.
2. Press Enter/Display 10 to select.
Tune or Seek Function (FM)
There are two tuning methods and one seek method for finding
the desired frequency.
clockwise
1
4 until the desired function
9 also puts the radio
until you reach
3
10 to perform the
to alternate between
10