Package Contents; Description (Fig. A) - DeWalt DCE530 Traducido De Las Instrucciones Originales

EngLIsH
Battery Type
The DCE530 operates on an 18 volt battery pack.
These battery packs may be used: , DCB181, DCB182, DCB183,
DCB183B, DCB184, DCB184B, DCB185, DCB187, DCB189,
DCB546, DCB547, DCB548. Refer to Technical Data for
more information.

Package Contents

The package contains:
1 Heat gun
1 Cone nozzle
1 Concentrator nozzle
1 Fish tail surface nozzle
1 Li-Ion battery pack (C1, D1, L1, M1, P1, S1, T1, X1, Y1 models)
2 Li-Ion battery packs (C2, D2, L2, M2, P2, S2, T2, X2, Y2 models)
3 Li-Ion battery packs (C3, D3, L3, M3, P3, S3, T3, X3, Y3 models)
1 Instruction manual
nOTE: Battery packs, chargers and kitboxes are not included
with N models. Battery packs and chargers are not included with
NT models. B models include Bluetooth® battery packs.
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by D WALT is under license. Other trademarks and
e
trade names are those of their respective owners.
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms may be shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Visible radiation. Do not stare into light.
Date Code Position (Fig. B)
11
The date code , which also includes the year of manufacture,
is printed into the housing.
Example:
2019 XX XX
Year of Manufacture

Description (Fig. A)


WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result. Use only D
battery packs with this product. Use of any other battery
may create risk of fire.
30
1 On/off trigger switch
2 Air vents
3 Air temperature
adjustment switch
4 Nozzle
5 Heat barrel cover
Intended Use
Your heat gun has been designed for stripping paint, soldering
pipes, shrinking PVC, welding and bending plastics as well as
general drying and thawing purposes.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
The heat gun is a professional power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
WALT
e
To actuate the fuel gauge, press and hold the fuel gauge
12
button . A combination of the three green LED lights will
6 Battery release button
7 Battery
8 Lock-on button
9 LED light
10 Trigger
WALT battery packs and chargers.
e
7
is fully charged.
7
with the rails inside the tool's
6
and firmly pull the battery pack