Power button
4
Brightness button
5
Date code (Fig. C)
6
Intended Use
This area light is designed for professional lighting applications.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
This area light is a professional power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
•
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Suspending/Mounting the Area Light
(Fig. C, D)
CAUTION: When the area light hangs by the hang hook or
hang inset, do not shake the light or the object from which it
hangs. Do not hang the area light from any electrical wires
or anything that is not secure. Personal injury or property
damage may occur.
CAUTION: Only use the hang hook or hang inset for
hanging the area light. The hang hook and hang inset are
not intended to support additional weight. Do not attach
or hang anything additional to the light or risk of breakage
may occur.
CAUTION: Do not use the hang hook to reach with.
Do not use the hang hook or hang inset to support your
weight in any situation.
CAUTION: Do not stand underneath the area light when
it is mounted overhead. Serious personal injury or damage
to the light may result if the light falls.
CAUTION: Do not mount the area light to the ceiling.
Your area light has multiple options for suspending or mounting.
Hang Hook (Fig. C)
The hang hook
7
is provided on the bottom of the area light to
allow suspending the light.
Hang Inset (Fig. D)
A cord may be used to hang the light by looping it through the
hang inset
13
found on the bottom of the light.
screw Threads (Fig. D)
Screw threads, 1/4"-20
8
and 5/8"-11
bottom of the area light to allow mounting to a tripod.
CAUTION: Use only with D
to ensure stability when mounted. Refer to Optional
accessories for more information.
9
, are provided on the
WALT heavy-duty tripod
e
1. Place the tripod's mounting screw into the appropriate
screw thread on the base of the light and screw the tripod
to the light.
2. Ensure the light is securely attached.
Carrying the Area Light (Fig. A)
Carry the area light using one or two of the four side handles
Never use the side handles to attach the light to anything. Refer
to Suspending/Mounting the Area Light.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
1. To install the battery pack
battery compartment door
the rails inside the battery compartment and slide it in until
the battery pack is firmly seated and latched. Ensure that it
does not disengage, then close the door.
2. To remove the battery pack from the area light, press the
battery release button
11
pull the battery pack out.
Fuel Gauge Battery Packs (Fig. B)
Some D
WALT battery packs include a fuel gauge which consists
e
of three green LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Do not store anything inside the battery compartment.
EngLIsH
WALT battery packs and chargers.
e
is fully charged.
10
10
into the area light, open the
12
, align the battery pack with
on the battery pack and firmly
2
.
25