Maclaren Techno XT Instrucciones De Montaje página 10

US
Instructions
• READ THESE INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THEM FOR FUTURE REFERENCE.
IMPORTANT:
• APPLY BOTH BRAKES WHEN PARKING THE STROLLER.
• YOUR CHILDREN'S SAFETY MAY BE AFFECTED IF YOU DO NOT FOLLOW THESE INSTRUCTIONS.
1 TO OPEN THE STROLLER
A Release storage clip.
B Open out the stroller.
C Using foot, push the footplate down fully to engage the primary lock.
WARNING:
locking devices are engaged before use.
2 TO OPERATE BRAKES
A TO ENGAGE BRAKES: With foot, pull the brake levers fully back.
B TO RELEASE BRAKES: Push the brake levers fully forward.
WARNING:
shall be engaged during the loading and
unloading of children.
3 TO OPERATE FRONT WHEEL SWIVEL LOCKS
A TO LOCK SWIVELS: Lift BOTH swivel locking levers.
B TO UNLOCK SWIVELS: Push down BOTH swivel locking levers.
4 SEAT BELT/SHOULDER HARNESS OPERATION
WARNING:
from falling or sliding out. Always use the
crotch strap in combination with the waist belt
and shoulder straps.
TO FIT HARNESS:
A Insert both fasteners securely into clasp.
B Adjust strap lengths. Belt, crotch strap and harness should be snug.
C 'D' rings are included for an additional harness, if desired.
TO RELEASE HARNESS:
D Squeeze fastener prongs and pull apart.
5 TO FIT HEAD CUSHION (if supplied)
A Unclip shoulder harness straps from clasp and pass through head
cushion holes.
B Attach Velcro straps to corresponding Velcro strips on seat rear.
6 TO FIT HARNESS PADS (if supplied)
A Lay open pad under shoulder harness strap.
B Fold pad over and secure Velcro strips.
7 TO OPERATE THE LEGREST
TO EXTEND THE LEGREST: Feel through seat corner openings. Locate sliders and pull
forward. Reverse this process to retract legrest.
8 TO ADJUST SEAT RECLINE
A TO RECLINE SEAT BACK: Lift both hand grips to release seat locks and slide the
seat back to desired position. Lower hand grips to engage locks
on both sides.
B TO RAISE SEAT BACK: From rear of stroller push seat back to original upright or
desired intermediate position.
Ensure that all
Parking device
Avoid serious injury
9 TO ATTACH THE HOOD
CAUTION: Overloading may cause a hazardous unstable condition to exist. Maximum
total capacity of hood pockets - 1.1lb (0.5 kg).
A With stroller open clip the hood to the handle tubes just above the
retaining blocks.
B Wrap velcro strips around handle tubes.
C Place rear apron behind seat back and attach poppers to seat sides (one
each side).
D Extend hood and press down on side hinges to lock open.
TO TILT HOOD:
E Fully unzip back panel.
F Tilt hood forward.
G Attach hood rear apron poppers to seat back when the seat is in the fully
reclined position.
H The hood is removed by firmly pressing down the clip release tabs.
10 TO ADJUST HANDLE LENGTHS
A Press triggers.
B Slide handles until triggers locate in one of 3 positions. Release triggers
to lock.
11 TO FIT THE RAIN APRON
A Return hood to non-tilted position before fitting rain apron.
B Ensure visor is folded away beneath the hood.
C Place the apron over the hood front.
D Attach two eyelets (one each side) to the hood clips.
E Attach the two eyelets (one each side) to the front legs.
12 TO FIT THE SHOPPING BAG
CAUTION: Overloading may cause a hazardous unstable condition to exist.
Maximum load 4.4lb (2kg) evenly distributed.
The stroller may be folded with the bag still attached but all contents must be
removed. Failure to do this could damage stroller and contents of shopping bag.
A Place bag on the 'X' frame under seat with lowest edge of bag at front.
B Attach front straps to front legs just below seat.
C Attach rear straps to rear legs just above horizontal tie bar.
13 TO FOLD THE STROLLER
Ensure visor is folded away beneath the hood.
Ensure the seat back is in its fullest upright position and the hood(if fitted) is folded
back.
Remove contents of shopping bag.
It is recommended that the harness is fastened before folding the stroller.
A Using foot, lift up on footplate to release primary lock.
B Push down on secondary lock lever.
C Grip handles and push forward.
D Compress folded stroller and engage the storage clip.
14 REMOVING AND REFITTING THE SEAT COVER
Remove hood, shoulder pads and seat retention straps from stroller if fitted.
A Twist shoulder strap end buckles and feed through holes.
B Feed waist strap fasteners through holes.
C Feed crotch strap buckle through holes.
D Unclip seat cover retaining straps.
E Unfasten seat fabric from handle tubes and seat base.
F Slide fabric from seat back and base.
G When refitting seat fabric, insert seat back support tubes into fabric flap.
H When refitting shoulder straps choose the jockey strap fabric holes appropriate
to the child's size. Twist the buckles and feed through seat cover, seat back and
then through holes in plastic seat back arms.
J When refitting seat fabric to seat base, choose the fabric holes
appropriate to the child's size. Loop fabric flap over legrest strap and pass
crotch strap buckle through both holes in seat fabric and then hole in
seat base.
3