Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
KIA Sorento EX 2003-2006 /
Sorento LX 2004-2006
KIT FEATURES
• ISO DDIN radio provision
KIT COMPONENTS
A) ISO DDIN brackets B) ISO DDIN trim plate
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-2003
Antenna Adapter: • 40-GM10
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
METRA. The World's best kits.
Installation instructions for part 95-1006
(Sport Package Only)
95-1006
metraonline.com
™
Table of Contents
Dash Disassembly ................................................. 2
Kit Assembly
–
ISO DDIN radio provision ...................................... 3
CAUTION!
Metra recommends disconnecting the negative bat -
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con -
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
Publicidad
Tabla de contenido
Manuales relacionados para Metra 95-1006
Resumen de contenidos para Metra 95-1006
- Página 1 KIT COMPONENTS A) ISO DDIN brackets B) ISO DDIN trim plate CAUTION! Metra recommends disconnecting the negative bat - tery terminal before beginning any installation, unless the vehicle manufacturer recommends against so. Please check with your local WIRING & ANTENNA CONNECTIONS (sold separately) Dealership for more information.
-
Página 2: Dash Disassembly
95-1006 Dash Disassembly 1. Open ashtray then unsnap and remove side trim panels. (Tip: start at the bottom of the panels) (Figure A) 2. Remove (8) Phillips head screws securing the radio trim panel. Unplug and remove panel. (Figure B) 3. -
Página 3: Kit Assembly
95-1006 Kit Assembly ISO DDIN radio provision 1. Slide the appropriate bracket into the ISO DDIN trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A) 2. Slide the radio into the completed... -
Página 4: Important
Installation instructions for part 95-1006 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. -
Página 5: Características
Sería mejor retirar la llave de la ignición y esperar unos HERRAMIENTAS REQUERIDAS cuantos segundos antes de quitar el radio de fábrica. • Herramienta para quitar paneles • Destornillador Phillips METRA. The World’s best kits. metraonline.com ™ © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION... - Página 6 95-1006 Desmontaje Dash 1. Abra el cenicero y luego suelte a presión y quite los paneles de moldura lateral. (Sugerencia: empiece en la parte de debajo de los paneles) (Figura A) 2. Quite los (8) tornillos de cabeza Phillips que sujetan el panel de la moldura del radio.
-
Página 7: Ensamble Del Kit
95-1006 Ensamble del kit Provisión de radio ISO DDIN 1. Deslice el soporte correspondiente en la placa de la moldura ISO DDIN, alineando los orificios de la placa de la moldura con los ganchos del soporte. (Figura A) 2. Deslice el radio en el ensamble terminado y sujételo al ensamble... -
Página 8: Importante
800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP). METRA. The World’s best kits. metraonline.com ™ © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION...