1. Manuales
  2. Marcas
  3. Metra Manuales
  4. Receptores para Coches
  5. 95-93078
  6. Manual del usuario

Metra 95-93078 Manual Del Usuario

Ocultar thumbs
1
2
3
4
5
6
7
8
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Descargar este manual
5-Series
M5
KIT FEATURES
• ISO DDIN radio provision
• Painted scratch resistant matte black
KIT COMPONENTS
• A) ISO DDIN radio housing • B) ISO DDIN radio trim plate • C) ISO DDIN brackets • D) (4) Panel clips
• E) (8) ISO screws • F) (2) #8 x 1/2" Phillips screws
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-9003 • 70-8590 • 70-8591
Antenna Adapter: • 40-EU10 • 40-VW10
TOOLS REQUIRED
• Phillips Screwdriver • Torx T-10 Screwdriver • Panel Removal Tool • Cutting Tool or File • Socket Wrench
METRA. The World's best kits.
Installation instructions for part 95-9307B
BMW 5 Series
1997-2003
(Without NAV)
2000-2003
(Without NAV)
95-9307B
C
D
™
E
F
metraonline.com
Table of Contents
Dash Disassembly .............................................. 2-3
Kit Assembly
– ISO DDIN radio provision ...................................... 4
CAUTION!
Metra recommends disconnecting the negative bat -
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con -
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION

Publicidad

Tabla de contenido
loading

Manuales relacionados para Metra 95-93078

Resumen de contenidos para Metra 95-93078

  • Página 1 • A) ISO DDIN radio housing • B) ISO DDIN radio trim plate • C) ISO DDIN brackets • D) (4) Panel clips • E) (8) ISO screws • F) (2) #8 x 1/2” Phillips screws CAUTION! Metra recommends disconnecting the negative bat - tery terminal before beginning any installation, unless the vehicle manufacturer recommends against so. Please check with your local WIRING &...

  • Página 2: Dash Disassembly

    95-9307B Dash Disassembly 1. Remove the volume knob by pulling 5. Remove the (1) Phillips screw out towards the rear of the vehicle. securing each side panel on the center console, and then slide 2. Turn the exposed screw 90º using the panels forward to unclip and a T-10 Torx screwdriver, pull out remove them.
  • Página 3 95-9307B Dash Disassembly 7. Remove the (2) Phillips screws 11. Carefully pull the right side of the securing the panel located inside the lower dash panel outward to gain left side of the glove box cavity, and access to the radio sub-dash panel, then remove the panel.

  • Página 4: Kit Assembly

    3. Locate the factory wiring harness and antenna connector in the dash and complete all necessary before calling. connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Reconnect the negative battery terminal and test the NOWLEDGE IS OWER radio for proper operation.

  • Página 5: Herramientas Requeridas

    Sería mejor retirar la llave de la ignición y esperar unos cuantos segundos antes de quitar el radio de fábrica. Adaptador de antena: • 40-EU10 • 40-VW10 METRA. The World’s best kits. metraonline.com ™ © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION...

  • Página 6: Desmontaje Del Tablero

    95-9307B Desmontaje del tablero 1. Quite la perilla del volumen jalando 5. Quite (1) tornillo Phillips que sujeta hacia la parte trasera del vehículo. cada panel lateral en la consola central, luego deslice los paneles 2. Gire el tornillo expuesto 90º usando hacia adelante para desengancharlos un destornillador Torx, jale la parte y quitarlos .
  • Página 7 95-9307B Desmontaje del tablero 7. Quite los (2) tornillos Phillips que 11. Jale con cuidado el lado derecho sujetan el panel al lado izquierdo del tablero central inferior hacia interior de la guantera, luego quite fuera para acceder al sub tablero el panel.

  • Página 8: Ensamble Del Kit

    Metra recomienda que use adaptadores problemas antes de llamar. adecuados de acoplamiento de Metra y/o de AXXESS. Vuelva a conectar la terminal negativa de la batería y EL CONOCIMIENTO ES PODER Mejore sus habilidades de instalación y...

Tabla de contenido