Intended Use - Silverline 802092 Manual Del Usuario

802092
Assembled
32. Adjustable Fence
33. Table Scale
34. Direction Indicator
35. Guard
36. Table Insert Mounting
37. Guard Moving Point
38. Feathers
39. Protractor
40. Featherboard Direction Indicator
41. Protractor Angle Scale
42. Protractor Knob
43. Vertical Featherboard
44. Main Fence
45. Protractor Channel
46. Bench Mounting Holes
47. Horizontal Featherboard Mounting
48. Mains Socket
49. On Button
50. Off Button
51. Adjustable Fence Knob
52. Adjustable Fence Scale
53. Adjustable Fence Indicator
54. Main Fence Knob
55. Dust Extraction Port
56. Vertical Featherboard Wingnut
57. Main Table
58. Horizontal Featherboard Knob
59. Horizontal Featherboard
Router Table with Protractor

Intended Use

Router table for temporary or permanent bench mounting or alternatively fitting to a dedicated tool
stand . Capable of edge rebating, trenching, cross trenching, planing, edge moulding (fence and
freehand), end grain work, jointing, using a template guide, and morticing. For use with the routers
from 900W to 1800W power with a circular or semi-circular base with a diameter 155mm or less.
Unpacking Your Tool
• Carefully unpack and inspect your tool. Familiarise yourself with all its features and functions
• Ensure that all parts of the tool are present and in good condition . If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
Before Use
WARNING: Ensure the tool is disconnected from the power supply before attaching or
changing any accessories, or making any adjustments.
Assembling the router table
See the exploded diagram at the beginning of the manual for a general quick view of how the table
fits together then follow the instructions below.
Table
1. Place the Table (1) upside down on a flat surface that will not scratch or damage the parts or allow
the parts to move
2. Line up the Table Extensions (3) ready for attachment on both ends of the Table
3. Fit one Leg (4) into the recess of the Table and insert a Phillips Head Bolt (9) through the Table
Extension, through the Table and finally through a mounting hole of the Leg. Fit a Nut (10) onto
the thread of the bolt and tighten loosely
Note: The Legs fit inside the underneath of the Table whereas the Table Extensions are mounted on
the external sides of the Table .
4. Repeat until the Leg is secured for that corner and then repeat for all Legs until the main Table,
Table Extensions and Legs are all fitted. Tighten so the Legs and Table Extensions can still be
moved by hand but hold the position they are left in. This allows for adjustment before final
tightening
5. Check the flat surface you are using is level with a spirit level for both axes. Turn the router table
over and check all the bench-mounting feet are level and flat on the surface. Use a spirit level to
check the Table and Table Extensions are level on both axes and adjust the position of the Legs
and Table Extensions if necessary
6. Once level carefully tighten the Nuts to lock that position. Do not over-tighten. Make sure the
router table remains level after tightening and does not rock
7. Attach the Switchbox (5) to the underside front of the Table using two Phillips Head Bolts (9) and
two Nuts (10)
8. Fit the Horizontal Featherboard using one of the Featherboards (30), both Featherboard Pads
(11), two Knobs (12) and both Fence Bolts (14). The pads should be placed into the channel of
the Table with the raised edges of the pads placed to the left and right side of the Featherboard
IMPORTANT: Note the direction of the Featherboard feathers in the main image of the Router Table .
It is important that both vertical and the horizontal Featherboards are facing the correct way to work
with the feed direction as shown.
silverlinetools.com
9