Charging Process; Important Safety Instructions For All Battery Packs - DeWalt DCD734 Traducido De Las Instrucciones Originales

SAVE THESE INSTRUCTIONS
Chargers
The DCB106 charger accepts 18 V Li-Ion (DCB180,
DCB181, DCB182, DCB183, DCB184 and
DCB185) battery packs.
The DCB107 charger accepts 10.8 V, 14.4 V and
18 V Li-Ion (DCB121, DCB123, DCB125, DCB127,
DCB140, DCB141, DCB142, DCB144, DCB145,
DCB180, DCB181, DCB182, DCB183, DCB184
and DCB185) battery packs.
This charger requires no adjustment and is designed
to be as easy as possible to operate.
Charging Procedure (fig. 2)
1. Plug the charger into an appropriate 230 V
outlet before inserting the battery pack.
2. Insert the battery pack (g) into the charger,
making sure the pack is fully seated in the
charger. The red (charging) light will blink
continuously indicating that the charging
process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life of
Li-Ion batteries, charge the battery pack fully before
first use.

Charging Process

Refer to the table below for the state of charge of
the battery pack.
State of charge–DCB106
charging
fully charged
State of charge–DCB107
charging ––
fully charged ––––––––––––––––––––
hot/cold pack delay ––
HOT/COLD PACK DELAY (DCB107)
The DCB107 charger has a hot/cold delay feature.
When the charger detects a battery that is hot, it
automatically delays charging until the battery has
cooled.
When the charger detects a battery that is cold, it
automatically delays charging until the battery has
warmed.
The red light will continue to blink, but a yellow
indicator light will be illuminated during this
operation. Once the battery has cooled, the yellow
light will turn off and the charger will resume the
charging procedure.
XR Li-Ion tools are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure
to include the catalog number and voltage.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below and then follow
the charging procedures outlined.
• Do not charge or use the battery pack
• Never force the battery pack into charger.
• Charge the battery packs only in designated
• DO NOT splash or immerse in water or other
–– –– –– ––
• Do not store or use the tool and battery
–––––––––––––––––
–– –– –– ––
• For best results, make sure the battery pack is
–– –– –––––––
READ ALL INSTRUCTIONS
in explosive atmospheres, such as in the
presence of flammable liquids, gases or
dust. Inserting or removing the battery pack
from the charger may ignite the dust or fumes.
Do not modify the battery pack in any way
to fit into a non-compatible charger as
battery pack may rupture causing serious
personal injury.
D WALT chargers.
E
liquids.
pack in locations where the temperature
may reach or exceed 40 ˚C (105 ˚F) (such
as outside sheds or metal buildings in
summer).
fully charged before use.
WARNING: Never attempt to open
the battery pack for any reason. If
the battery pack case is cracked or
damaged, do not insert it into the
charger. Do not crush, drop or damage
battery pack. Do not use a battery
pack or charger that has received a
sharp blow, been dropped, run over
or damaged in any way (e.g., pierced
with a nail, hit with a hammer, stepped
EN GL IS H
37