Assembly And Adjustment - DeWalt D28127 Manual De Instrucciones

Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1.5 mm 2 .
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
2
Conductor size (mm )
0.75
1.00
1.50
2.50
4.00
Voltage Amperes
115 0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230 0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0

Assembly and adjustment

Prior to assembly and adjustment always
unplug the tool.
Mounting and removing the guard (fig. B)
• Place the angle grinder on a table, spindle up.
• Release the clamping lock (6) and hold the guard
(4) over the tool as shown.
• Align the lugs (7) with the notches (8).
• Press the guard down and rotate it to the
required position.
• If required, increase the clamping force by
tightening the screw (9).
• Tighten the clamping lock.
• To remove the guard, release the clamping lock.
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5 15 25 30 45
Cable rating (Amperes)
6 6 6 6
6 6 6 6 15
6 6 10 15 20
10 10 15 20 20
15 15 20 25 25
20 20 25 -
6 6 6 6
6 6 6 6
6 6 6 6 10
10 10 10 10 15
15 15 15 15 20
20 20 20 20 25
Fitting and removing a grinding or cutting disc
(fig. C1 & C2)
• Place the tool on a table, guard up.
• Fit the inner flange (10) correctly onto the spindle
(11) (fig. C1).
• Place the disc (12) on the flange (10). When
fitting a disc with a raised center, make sure that
the raised centre (13) is facing the flange (10).
• Screw the outer flange (14) onto the spindle (11)
(fig. C2):
- the ring on the flange (14) must face towards
the disc when fitting a grinding disc (A);
- the ring on the flange (14) must face away from
the disc when fitting a cutting disc (B).
60
• Press the spindle lock (3) and rotate the spindle
(11) until it locks in position.
6 10
• Tighten the flange (14) with the two-pin spanner
15
supplied.
20
• Release the spindle lock.
25
• To remove the disc, loosen the flange (14) with
-
the two-pin spanner.
- -
6 6
6 6
15
Fitting a wire cup brush
15
• Screw the wire cup brush directly onto the spindle
20
without using the spacer and threaded flange.
-
Mounting and removing the rubber backing pad
(fig. D)
The rubber backing pad is available as an option.
• Remove the guard from the tool.
• Press the backing pad (15) onto the spindle (11).
The inner flange is not needed.
• Position the abrasive disc (16) on the pad.
• Screw the outer flange (14) onto the spindle (11).
• Press the spindle lock and rotate the pad (15)
until it locks in position.
• Tighten the flange (14) using the two-pin spanner
supplied.
• Release the spindle lock.
• To remove the pad, loosen the flange (14) with
the two-pin spanner.
Never use the tool without the guard in
place.
Do not use a damaged disc.
E N G L I S H
23