Assembly And Adjustment - DeWalt DW811 Manual De Usuario

input of this tool (see technical data). The minimum
conductor size is 1.5 mm
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
2
Conductor size (mm )
0.75
1.00
1.50
2.50
4.00
Voltage Amperes
115 0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
220/240 0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0

Assembly and adjustment

Prior to assembly and adjustment always
unplug the tool.
Connecting the cable to the tool (fig. B)
• Move the slider (6) completely in the direction of
the arrow on the tool.
• Push the cable connector firmly into the socket (7).
• Move the slider (6) completely back to secure the
cable.
Mounting and removing the guard (fig. C & D)
Mounting
• Place the Angle Grinder on a table, spindle up.
• Align the lug (8) with the slot (9) in the bracket.
• Press the guard (3) down and turn it in the
direction of the arrow (fig. C).
The guard locking pin (10) prevents the
guard from coming loose.
15
2 .
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5 15 25 30 45
Cable rating (Amperes)
6 6 6 6
6 6 6 6 15
6 6 10 15 20
10 10 15 20 20
15 15 20 25 25
20 20 25 -
6 6 6 6
6 6 6 6
6 6 6 6 10
10 10 10 10 15
15 15 15 15 20
20 20 20 20 25
Removing
• Hold the tool in your hand.
• Rotate the guard (3) in the direction of the arrows
(fig. D).
• Use a screwdriver to press the locking pin (10) in
the slot.
• Release the guard.
Mounting and removing a grinding wheel or
cutting disk (fig. E & F)
DW811
• Place the tool on a table, guard up.
• Fit the spacer (12) correctly onto the spindle (11).
• Place the grinding wheel or cutting disk on the
60
spacer.
• Screw the threaded flange (13) onto the spindle (11).
6 10
• Press the spindle lock (5) and rotate the grinding
15
wheel or cutting disk until it locks in position.
20
• Tighten the threaded flange using the two-pin
25
spanner (14) supplied.
-
• Release the spindle lock.
- -
• To remove the grinding wheel or cutting disk,
6 6
loosen the threaded flange using the two-pin
6 6
spanner.
15
15
DW816
20
• Place the tool on a table, guard up.
-
• Fit the spacer (12) correctly onto the spindle (11).
• Place the grinding wheel or cutting disk on the
spacer.
• Screw the threaded flange (13) onto the spindle (11).
• Place a #14 wrench on the flat sides of the
spindle and tighten the threaded flange using the
two-pin spanner (14) supplied.
• To remove the grinding wheel or cutting disk,
loosen the threaded flange using the two-pin
spanner.
Fitting a wire cup brush
• Screw the wire cup brush directly onto the
spindle without using the spacer and threaded
flange.
Mounting and removing the rubber backing pad
(fig. G)
The rubber backing pad is available as an option.
DW811
• Remove the guard from the tool.
• Press the backing pad (16) onto the spindle (11).
E N G L I S H
en - 4