STEINEL 170 Serie Manual Del Usuario página 10

Serie 170-190_10spr.qxd
Selecting dimmer setting of your choice:
- Hold button down until LED flashes (in lens).
- Keep button pressed, the system will slowly run
through dimmer range from 0–100%.
- Release button when chosen setting is reached.
The LED will now continue flashing for about 5 sec.
This period may be used for optimising the dimmer
setting.
Permanent light
If a mains switch is installed in the mains supply lead,
the light is capable of the following functions in add-
ition to the simple ON/OFF function:
Sensor operation
1) Switch light on:
Switch 1 x OFF and ON.
Light stays on for the period selected.
2) Switch light off:
Switch 1 x OFF and ON.
The light goes out or switches to sensor mode.
Permanent light
1) Select permanent light:
Switch 2 x OFF and ON. The light is set to stay on for
4 hours (red LED lights up behind lens). Then it
returns automatically to sensor mode (red LED off).
2) Deactivate permanent light:
Switch 1 x OFF and ON. The light goes out or
switches to sensor mode.
Important:
The switch should be actuated in rapid succession
(in the 0.5 – 1 sec. range).
Reset function
The light can be returned to its original settings at any
time (daylight operation 2000 lux, 'on' time 10 sec.
and dimmer off).
To do this, hold all three buttons down at the same
time until the LED (in the lens) comes on and goes out
again (approx. 5 sec.).
Soft light start
The SensorLight features a soft light start function.
This means that when switched ON, the light does
not switch directly to maximum output but gradually
builds up brightness to 100% within the space of a
second. Brightness is also gradually reduced when
the light is switched OFF.
Basic reach setting
The sensor lens is divided into two detection zones.
One half covers a max. reach of 5 m, the other half a
max. reach of 12 m (when installed at a height of
31.07.2008 12:35 Uhr
approx. 2 m). After fitting the lens (firmly clamp lens
into the groove provided), a small arrow marks the
selected max. reach of 12 m or 5 m (arrow left =
5 metres, arrow right = 12 metres).
Using a screwdriver, the lens can be unclipped from
the groove at the side and re-positioned for the reach
you require.
Shrouds may be used to define the detection zone
exactly as you require in order, for example, to blank
out or specifically target paths or neighbouring prem-
ises. The shrouds can be divided or cut with a pair of
scissors along the vertical and horizontal grooves.
They can be clipped into the top channel around the
centre of the lens. They are fixed in place by fitting
the cover
(Examples showing how to reduce the angle of detec-
tion and shorten reach.)
The SensorLight is suitable for switching on light
automatically. Weather conditions may affect the way
the SensorLight works. Strong gusts of wind, snow,
rain or hail may cause the light to come on when it is
not wanted because the sensor is unable to distin-
guish sudden changes of temperature from sources
of heat. The detector lens may be cleaned with a
damp cloth if it gets dirty (do not use cleaning
agents).
Note (170/180 series):
Stainless steel should be cleaned at regular
intervals (about every 3 months) with a
standard stainless steel cleaner. If it is
not cleaned, corrosion may occur on the
surface (flash rust). Excellent results are
achieved with SIDOL CERAN & steel
cleaner from Henkel when applied along
the grain of the stainless steel brushed
finish. Do not use chlorine-based cleaning products.
This product complies with the European Directive on
Low-Voltage Appliances, 73/23/EEC and the EMC
Directive 89/336/EEC.
- 10 -
Seite 11
Precision adjustment with shrouds
.
Operation/Maintenance
Declaration of conformity