Black and Decker BDALLI18 Manual Del Usuario página 7

Do not damage/deform the battery pack either by puncture
u
or impact, as this may create a risk of injury and fire.
Do not charge damaged batteries.
u
Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries, carefully wipe the
liquid off using a cloth. Avoid skin contact.
In case of skin or eye contact, follow the instructions
.
below
Warning! The battery fluid may cause personal injury or
damage to property. In case of skin contact, immediately
rinse with water. If redness, pain or irritation occurs
seek medical attention. In case of eye contact, rinse
immediately with clean water and seek medical attention.
Chargers
Warning! Your charger has been designed for a
specific voltage. Always check that the mains voltage
corresponds to the voltage on the rating plate.
Warning! Never attempt to replace the charger unit with a
regular mains plug.
Use your BLACK+DECKER charger only to charge the
u
battery in the appliance/tool with which it was supplied.
Other batteries could burst, causing personal injury and
damage.
Never attempt to charge non-rechargeable batteries.
u
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKERService
Centre in order to avoid a hazard.
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
u
The charger must be placed in a well ventilated area when
u
charging.
Labels on the charger (not included with GKC1000LB)
The following symbols are found on your charger:
The charger is intended for indoor use only.
Read the instruction manual before use.
Electrical safety
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
1. Top jaw
(Original instructions)
2. Lower jaw
3. Chain guide bar
4. Oiling cover
5. Latch
6. Battery
7. On/off switch actuators
8. Chipping ejection point
9. Charger
Assembly
Warning! Before assembly, remove the battery (6) from the
tool.
Fitting and removing the battery (fig. A)
To fit the battery (6), line it up with the receptacle on the
u
tool. Slide the battery (6) into the receptacle and push until
the battery (6) snaps into place.
To remove the battery (6), push the release button (18)
u
while at the same time pulling the battery (6) out of the
receptacle.
Opening the handles (fig. B)
To open the handles, slide the latch (5) backwards and
u
pull the handles apart.
After use, close the handles and slide the latch (5) forward
u
to the lock position. The handles should be locked during
transportation and storage.
Chain tension adjustment (fig. C)
Warning! Before adjusting the chain tension or any other
adjustments, make sure that the tool is switched off and the
battery removed.
Warning! The chain guide bar and the saw chain may be hot
after use. Allow to cool before adjustment.
The product comes ready assembled. However we
recommend that you check the tension of the saw chain (14),
and chain access cover retention bolts before use and adjust
if required.
Checking and adjusting the saw chain tension (fig.
C)
To tension the saw chain (14) slacken the two chain cover
retention bolts (12) with the spanner (13) and the chain
tensioning device will push the chain guide bar (3) out, setting
the correct tension. Retighten the two retention bolts (12)
securely.
Check the correct tension has been set by lightly pulling on
the saw chain (14). The tension is correct when the saw chain
snaps back after being pulled 3 mm away from the guide bar.
There should be no "sag" between the chain guide bar (3) and
the saw chain (14) on the underside.
Note: Do not over tension the saw chain as this will lead to
excessive wear and reduce the life of the bar and saw chain.
ENGLISH
7