Black and Decker BDALLI18 Manual Del Usuario página 8

ENGLISH
It will also lead to reduced product performance.
Note: With first use and when the saw chain is new, check
tension frequently as a new saw chain stretches slightly.
Replacing the saw chain and chain guide bar
After prolonged use the saw chain (14) and /or chain guide
bar (3) may need replacing. Ensure only Black & Decker
recommended replacements are used.
Removing the saw chain and chain guide bar (fig.
C & D)
Always wear protective gloves when installing
or removing the saw chain (8). The saw chain is
sharp and can cut you when it is not running.
Warning! The chain guide bar and the saw chain may be hot
after use. Allow to cool before replacing.
Place the tool on a firm surface.
u
Rotate the two retention bolts (12) counter clockwise with
u
the spanner (13) provided and remove completely.
Remove the chain access cover (11).
u
Slide the latch (5) to the unlock position, open the handles
u
and pull back the top jaw (1).
Pull back chain guide bar (3) and then lift the saw chain
u
(14) out of the groove in the guide bar. The saw chain can
then be removed from the unit.
The chain guide bar (3) can then be angled up and
u
removed.
Assembling the chain guide bar and saw chain (fig.
E & F)
Warning! Always wear protective gloves when installing or
removing the saw chain. The saw chain is sharp and can cut
you when it is not running.
Ensure the operation is carried out on a firm surface.
u
Slide the latch (5) to the unlock position, open the handles
u
and pull back the top jaw (1).
Insert the chain guide bar (3) into the space between the
u
chain tensioner and align with the chain guide bar locator,
angle the chain guide bar (3) down ensuring it is correctly
located.
Place the saw chain (14) around the front of the chain
u
guide bar (3).
Pull the chain guide bar (3) and the saw chain (14) back,
u
engaging it in the groove in the chain guide bar (3) and
then over the sprocket (16) positioning teeth in the correct
position on the sprocket.
Replace the chain access cover (11) and the two retention
u
bolts (12) tightening securely.
Ensure the saw chain (14) is fitted correctly with reference
u
to the markings on the tool.
8
(Original instructions)
Oiling (fig. G)
Before first use and every ten minutes of use you must
u
oil the product with the correct chain oil. (Cat No A6027)
Open the oiling cover (4) and insert the bottle into the
oil filling hole (15), apply pressure to the bottle once to
dispense oil.
This should be adequate for about 10 minutes of cutting
u
depending upon cutting speed and type of wood.
The hole feeds the oil through to the saw chain on to the
chain guide bar (3) and an excessive amount of oil applied to
the unit could mean the oil drips from the unit around the jaw
area. This is normal and is nothing to be concerned about.
Use
Charging the battery (fig. H)
Warning! Do not charge the battery at ambient temperatures
below 10°C or above 40°C. Recommended charging
temperature is approximately 24°C.
Note: The charger will not charge a battery pack if the cell
temperature is below approximately 0°C or above
40°C.The battery should be left in the charger and the
charger will begin to charge automatically when the cell
temperature warms up or cools down.
To charge the battery (6), insert it into the charger (9). The
u
battery will only fit into the charger one way. Do not force.
Make sure that the battery pack is fully seated in the
u
charger (9).
Plug in the charger (9) and switch on at the mains.
u
The charging indicator (19) will flash continuously (slowly).
u
The charge is complete when the charging indicator (19)
u
lights green continuously.
The LED will change to flashing green (charging) state as
u
the charger occasionally tops up the battery charge.
The charging indicator (19) will be lit as long as the battery
u
pack is connected to the plugged in charger (9).
Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the
charging indicator will flash red at a fast rate. Proceed as
follows:
Re-insert the battery (6).
u
If the charging indicator (19) continues flashing red at
u
a fast rate, use a different battery to determine if the
charging process works properly.