Black and Decker BDT555KIT Manual De Instrucciones página 8

ENGLISH
Connecting the tool to the mains (fig. F)
Connect the female plug of a suitable extension cable to
u
the power inlet (4).
Loop the cable through the cable restraint (3).
u
Insert the mains plug into a mains outlet.
u
For wired in cable units: Make sure the cable is looped
through the cable restraint prior to connecting the plug to the
mains outlet.
Use
Warning! Let the tool work at its own pace. Do not overload.
Setting the tool to trimming or edging mode (fig.
G,H, I & J)
The tool can be used in trimming mode as shown in fig. I or in
edging mode to trim overhanging grass along lawn edges and
flower beds as shown in fig. J.
Trimming mode (fig. E, G & I)
For trimming, the trimmer head should be in the position
shown in fig. I. If it is not:
Disconnect the tool from the supply.
u
Loosen the adjustment collar (14) by turning it clockwise.
u
Whilst holding the handle (2), rotate the head (8) clock-
u
wise.
Tighten the collar (14) by turning it anti-clockwise.
u
Note: The head will only rotate in one direction.
Edging mode (fig. E, H & J)
For edging, the trimmer head should be in the position shown
in fig. J. If it is not:
Disconnect the tool from the supply.
u
Loosen the adjustment collar (14) by turning it clockwise.
u
Whilst holding the handle (2), rotate the head (8) anti-
u
clockwise.
Tighten the collar (14) by turning it anti-clockwise.
u
Note: The head will only rotate in one direction.
Switching on and off
To switch the tool on, squeeze the trigger lever (1).
u
To switch the tool off, release the trigger lever.
u
Warning! Never attempt to lock the trigger lever in the on
position.
Hints for optimum use
General
In order to achieve optimum cutting results, only cut dry
u
grass.
Trimming
Hold the tool as shown in fig. I.
u
Gently swing the trimmer from side to side.
u
8
(Original instructions)
When cutting long grass, work in stages from the top. Take
u
small cuts.
Keep the tool away from hard objects and delicate plants.
u
Cutting line will wear faster and require more feeding if
u
the cutting is done along pavements or other abrasive
surfaces or heavier weeds are being cut.
If the tool starts running slowly, reduce the load.
u
Edging
Optimum cutting results are achieved on edges deeper than
50 mm.
Do not use the tool to create edges. To create edges, use
u
an edging spade.
Guide the tool on its wheel (9) as shown in fig. J.
u
To make a closer cut, slightly tilt the tool.
u
Fitting a new spool of cutting line (fig. K)
Replacement spools of cutting line are available from your
BLACK+DECKER dealer (cat. no. A6481).
Unplug the tool.
u
Keep the tabs (16) depressed and remove the spool cover
u
(17) from the spool housing (7).
Remove the empty spool (18) from the spool housing.
u
Remove any dirt and grass from the spool cover and
u
housing.
Take the new spool and push it onto the boss in the spool
u
housing. Rotate the spool slightly until it is seated.
Unclip the end of the cutting line and guide the line into
u
the eyelet (19). The line should protrude approx. 11 cm
from the spool housing.
Align the tabs (16) on the spool cover with the cut outs
u
(20) in the spool housing.
Push the cover onto the spool housing until it snaps
u
securely into place.
Warning! If the cutting lines protrude beyond the trimming
blade (21), cut them off so that they just reach the blade.
Winding new line onto an empty spool (fig. L, M &
N)
You may wind new cutting line onto an empty spool.
Replacement packs of cutting line are available from your
BLACK+DECKER dealer (cat. no. A6170 (25 m), A6171 (40
m)).
Remove the empty spool from the tool as described
u
above.
Remove any remaining cutting line from the spool.
u
Feed 2 cm of cutting line into the hole (22) in the spool as
u
shown (fig. L).
Bend the cutting line and anchor it in the L-shaped slot
u
(23).
Wind the cutting line onto the spool in the direction of the
u
arrow. Make sure to wind the line on neatly and in layers.
Do not criss-cross (fig. N).