Assembly And Adjustments - DeWalt DWST1-81078 Traducido De Las Instrucciones Originales

EngLIsh
Intended Use
The D WALT TSTAK™ CONNECT RADIO/CHARGER includes a
e
built-in FM and DAB radio, Bluetooth support and a 3.5 mm AUX
connector port to play audio/music from an external appliance.
An intuitive application for remote controlling the system
via a Bluetooth-enabled smartphone or tablet is available to
download from both the Google and Apple app stores. The
system includes charging capabilities for D
batteries. The TSTAK™ CONNECT RADIO/CHARGER will charge
most D WALT Li-ion batteries. Batteries sold separately.
e
DO nOt use under wet conditions or in the presence of
flammable liquids or gases.
Do not let children come into contact with the tool. Supervision
is required when inexperienced operators use this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
Inserting and Removing the Battery Pack
from the Radio/Charger (Fig. A)
nOtE: Make sure your battery pack
To Install the Battery Pack into the
Radio/Charger
1. Align the battery pack 13
receptacle 14 .
2. Slide it into the receptacle until the battery pack is firmly
seated in the tool and ensure that you hear the lock snap
into place.
To Remove the Battery Pack from the
Radio/Charger
1. Press the release button 22
out of the battery receptacle.
2. Insert battery pack into the radio/charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. A)
Some D WALT battery packs include a fuel gauge which consists
e
of three green LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 23 . A combination of the three green LED lights will
30
WALT slide pack
e
WALT battery packs and chargers.
e
13 is fully charged.
with the rails inside the battery
and firmly pull the battery pack
illuminate designating the level of charge left. When the level of
charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOtE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
OPERATIONS
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: Do not place the radio in locations where it
may be exposed to dripping or splashing.
Your Bluetooth® radio/charger is equipped with memory
capacity in order to store the time and your selected memory
channels. When the radio is in the OFF position, this memory
capacity is powered by one coin cell battery that is included
with the radio/charger.
Power/Volume Adjustment
1. To turn the radio/charger on, long press the selection
dial 18 .
2. Turn the dial 18 clockwise to increase the volume. To
decrease the volume, turn anti-clockwise.
Mode Function
To choose one of the mode functions ('DAB' , 'FM', or 'AUX' or
Bluetooth®) push the home button
mode using the touch keys 21
DAB Mode
tuning
When the unit is first switched on the unit will start in
'DAB'/'DAB+' mode and will 'Auto Scan' to find broadcast
stations in the local area. Once 'Auto Scan' is complete, short
press the selection dial 18 to enter the DAB menu. Select
ST.LIST (Station List) using the touch keys
selection dial 18 to select the desired station.
nOtE: When moving locations or if reception was poor in the
original scan (possible if the antenna was not up), this may result
in an empty or incomplete list of available stations. Manually
running a 'Full Scan' will find all available broadcast stations.
to Perform an auto scan:
1. Enter DAB mode and navigate to the menu by
short-pressing the selection dial
using the touch buttons 21
Display
Enter DAB mode and navigate to the menu by short-pressing
the selection dial 18 . Select INFO using the touch buttons
Choose the desired information to display using the touch
buttons 21 , then press the back button
20 , then select the desired
.
21 , then rotate the
( 18 . Select FULL SCAN
.
21
16 twice to return.
.