Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
I
KEY DIMENSIONS
AND SPECIFICATIONS
Description
Top-Loading
Washer
Rated Voltage/Frequency
120VAC, 60Hz
Dimensions
27"(W)
X 28 3/8"(D)
X 40 1/8"(H), 55 1/8"(H with lid open)
68.6 cm (W) X 72.1 cm (D) X 102 cm (H), 140 cm (H with lid open)
Net Weight
137.3 Ibs. (62.3 kg)
1
CHOOSE THE PROPER LOCATION
WARNING
• Washer is heaw/. Two or more people are required
when
moving and unpacking the washer. Failure
to do so may result in damage to property or serious
bodily
harm.
• Store and install the washer where it will nat be
exposed to temperatures
below freezing or exposed
to outdoor weather
conditions. Failure to follow this
warning
can cause serious injury, fire, electric
shock, or
death.
• Properly ground washer to conform with all electric
governing codes and ordinances.
Failure to follow this
warning
can cause serious injury, fire, electric
shock, or
death.
• To reduce the risk of electric shock, do not install
the washer in humid spaces. Failure to follow this
warning
can cause serious injury, fire, electric
shock, or
death.
• To ensure proper air flow, do not block the large
opening on the bottom of the washer with carpeting
or other materials.
• Do not remove ground prong. Do not use an adapter
or extension cord. Plug into a grounded 3-prong
outlet. Failure to follow this warning
can cause serious
injury, fire, electric
shock, or death.
Power Outlet
• The power outlet must be within 60 in. (1.5 m) of either
side of the washer.
• The appliance
and outlet must be positioned
so that
the plug is easily accessible.
• Do not overload
the outlet with more than
one appliance.
• The outlet must be grounded
in accordance
with
current wiring electric
codes and regulations.
• Time-delay
fuse or circuit breaker
is recommended.
NOTE: It is the personal responsibility
and obligation
of
the product owner to have a proper outlet installed by a
qualified
service technician.
1
FLOORING
• To minimize
noise and vibration,
the washer MUST be
installed
on a solidly constructed
floor. See the NOTE
to your right.
• Allowable
slope under the entire washer is a maximum
1 in. difference
from side to side or from front to back.
7
• Installing on carpeting
and soft tile surfaces is
not recommended.
• Never install the washer on a platform
or weakly
supported
structure.
1
CLEARANCES
40 I/8"
(102 cm)
1"
27"
1"
(2.5cm)
(68.6 cm)
To ensure sufficient clearance
for water lines and airflow,
allow minimum clearances of at least 1 in. (2.5 cm) at the
sides and 4 in. (10 cm) behind the unit. Be sure to allow
for wall, door, or floor moldings that may increase the
required clearances.
32
"
-_
(81 .I cm)
28
3/8"
I
(72.1 cm)
I-"
-I
55 1/8"
(140 cm)
(with
open lid)
_ii!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i
F263,4,,
_1
(68 cm)
3 2/4"
(g cm)
Minimum
vertical
space from floor to overhead
shelves,
cabinets, ceilings, etc., is 56 in.
NOTE: The washer must be installed on firm flooring to
minimize vibration during the spin cycle. Concrete flooring
is best, but a wood floor is sufficient, provided it is built
to FHA standards. The washer should not be installed on
rugs or exposed to weather.
Publicidad
Capítulos
Tabla de contenido
