Klein Tools NCVT-2 Manual Del Usuario página 3

Cleaning Tester:
• Tester contains sensitive electronic components; do not submerse in liquid.
• Do not use alcohol, ammonia or cleaners containing solvents to clean tester.
• Gently wipe the tester with Klein Kleaners
a cloth containing a mild cleaning solution.
• Make sure the tester is completely dry prior to operation.
DISPOSAL:
• Do not throw depleted batteries away; please recycle properly.
• Do not throw tester away, please recycle properly.
• Please see www.epa.gov or www.erecycle.org for additional information.
WARRANTY: www.kleintools.com/warranty
wARNINGS:
• It is important that users of this tester read, understand, and follow all warnings, cautions, safety
information, and instructions in this manual before operating or servicing this tester. Failure to
follow instructions could result in death or serious injury.
• Risk of electric shock and burn. Contact with live circuits could result in death or serious injury.
• Use caution with voltages above 30V AC as a shock hazard may exist.
• A blinking or steady red glow and an audible beep indicate voltage present. If no indication, voltage
could still be present.
• Never assume neutral or ground wires are de-energized. Neutrals in multi-wire branch circuits may be
energized when disconnected and must be retested before handling.
• The tester WILL NOT detect voltage if:
• the wire is shielded.
• the operator is not grounded or is otherwise isolated from an effective earth ground.
• the voltage is DC.
• The tester MAY NOT detect voltage if:
• the user is not holding the tester.
• the user is insulated from the tester with a glove or other materials.
• the wire is partially buried or in a grounded metal conduit.
• the tester is at a distance from the voltage source.
• the field created by the voltage source is being blocked, dampened, or otherwise interfered with.
• the frequency of the voltage is not a perfect sine wave between 50 and 500Hz.
• the tester is outside of operation conditions (listed in Specifications section).
• Operation may be affected by differences in socket design and insulation thickness and type.
• In bright light conditions, the LED visual indicators will be less visible.
• Do not use if "power on" LED is not illuminated.
• Do not use if tester appears damaged or if the tester is not operating properly. If in doubt, replace the tester.
• Do not apply more than the rated voltage as marked on the tester (1000 volts AC).
• Detection above 12V is specified under "normal" conditions as specified below. The tester may
detect at a different threshold at different conditions, or may not detect at all unless:
• The tip of the tester is within 0.25" of an AC voltage source radiating unimpeded.
• The user is holding the body of the tester with his or her bare hand.
• The user is standing on or connected to earth ground.
• The air humidity is nominal (50% relative humidity).
• The tester is held still.
• Always wear approved eye protection.
• Comply with local and national safety requirements.
• If this product is used in a manner not specified by the manufacturer, protection provided by the
product may be affected.
CAuTION:
• Do not attempt to repair this tester. It contains no serviceable parts.
• Do not expose the product to extremes in temperature or high humidity.
SPECIFICATIONS:
VOLTAGE RANGE: 12-1000 Volts AC
TESTER TYPE: Non-Contact Voltage Detector
UL CERTIFICATION
E321008 3TMV
FREQUENCY RANGE:
50-500Hz
STAN DARDS:
UL 61010-1 2
nd
61010-1-04, EN 61010-1 2
61010-1:2001 2
(IEC61010-1 MOD)
CAT IV RATED: 1000 V
DOUBLE INSULATED
POWER ON INDICATOR AND ILLUMINATOR:
Visual: High Intensity Green/Blue LED
POWER OFF & AUTO POWER OFF:
Visual: High Intensity Green LED Blinks
Audible: Double Beeping Sound
LOW BATTERY INDICATORS:
Visual: Green/Blue LED Blinks
Audible: Series of Beeping Sounds
edition, CAN/CSA C22.2 No.
edition, IEC
nd
edition, ISA-82.02.01
nd
CAT
IV
(CAT. # 51425), a damp cloth or
®
VOLTAGE DETECTION INDICATORS:
12 VOLTS TO 48 VOLTS:
Visual: High Intensity Blinking Red LED
Audible: Low Pitched, Pulsing Beeping Sound
48 VOLTS TO 1000 VOLTS
Visual: High Intensity Continuously
Illuminated Red LED
Audible: High Pitched, Continuous
Beeping Sound
OPERATING CONDITIONS:
Temperature: 32° to 104° F (0° to 40° C)
Relative Humidity: <80%
Altitude: Up to 6,562 feet (2,000 meters) max.
Environment: Indoor Use
STORAGE CONDITIONS:
Temperature: 32° to 104° F (0° to 40° C)
Relative Humidity: <80%
Altitude: Up to 6,562 feet (2,000 meters) max.
Environment: Indoor
POLLUTION DEGREE: 2
BATTERIES: Two 1.5 volt AAA
or IEC LR03 or NEDA 24A
PATENTS: US D583,266 S
DISPOSAL: DO NOT THROW IN TRASH;
PLEASE RECYCLE.