Tabla de contenido
Publicidad
12
www.raider.bg
Detail, and attach with appropriate appliances or braces is anchored more firmly and securely than if
you hold it by hand.
5.13. Keep your workplace clean.
Mixtures of different materials are particularly hazardous. Fine shavings from light metals can be
samovazplamenyat or explode.
5.14. Do not use the impact drill, where the power cord is damaged. If during operation the cable is
damaged, do not touch. Immediately disconnect the plug from the outlet.
Damaged power cables increase the risk of electric shock.
Failure of the considered instructions may lead to electric shock, fire and / or severe injuries.
6. Functional description and purpose of the impact drill.
Impact power hand drills are in class II insulation. They are powered by a collector single-phase motor,
the speed of revolutions is reduced by means of gear. This kind of power is widely used for boring
holes in wood, dendroid materials, metal, ceramics and synthetic materials in the working mode without
impact, as well as concrete, brick and similar materials in the operating mode of attack. Power electronic
controls for right and left direction of rotation can be used to develop cornering or screw joints. The areas
of use are carrying out repair and construction, carpentry and other work-related self-amateur activity ..
Not permitted the use of power tools for activities other than its intended purpose.
7. Information on noise and vibration emitted
The values are measured according to EN 60745. A level of noise generated is generally: the sound
pressure level 92 dB (A); sound power 102 dB (A). Uncertainty K = 3 dB. Work with a silencer! The
resultant value of vibration (the vector sum of the three directions) is determined according to EN 60745:
Drilling in metal: the value of the emitted vibrations a
= 6,13 m/s
, uncertainty K = 1,5 m/s
, hammer
2
2
h
drilling in concrete: value the emitted vibrations a
= 7,23 m/s
, uncertainty K = 1,5 m/s
, cornering /
2
2
h
development: the value of the emitted vibrations ah <2,5 m/s
, uncertainty K = 1,5 m/s
. That in this
2
2
operating manual for the vibration value is measured by the method specified in EN 60745 and can be
used to compare different power. The level of vibration varies depending on the specific activity carried
out and in some cases may exceed that amount in that direction. If power is used for a long time in this
mode, the load caused by vibration, could be underestimated. Directions: For an exact estimate of the
burden of vibrations in a working cycle should be recorded and the intervals in which the power is off
or idling. This can significantly reduce the reporting burden of vibrations throughout the business cycle.
8. Preparing for the job. Installation of accessories and auxiliary tools.
8.1.1. Auxiliary handle.
Use only the impact drill fitted with an auxiliary handle. You can insert auxiliary handle in practically
any position, to ensure your comfortable and safe position for the job. Turn the handle itself axis and
counterclockwise, thus reducing the firmness of the loop around the head of the drill and you can rotate
the handle vspomagatelnata in the desired position. Then tighten the grip again, such as turning it
clockwise.
8.2. Setting the depth of drilling. With deep baffle (5) can be pre-set depth of drilling. Pull the baffle so
deep that the distance along the axis between the tip of the drill and deep baffle is equal to the desired
depth of the hole.
8.3. Placing the drill in the chuck. Turn off the power of power. Put the key in one of the open side of
the chuck. Dissolving the jaws to the desired size and place in the drill chuck. With key-locking in three
successive drill a hole in the chuck. We must always remember that the key should be removed from the
drill after the completion of operations related to installation and dismantling of the drill. When mounting
a new drill should be checked by the inclusion of a short drill, drill that rotates in an axis without "flicker".
This will help us make sure that it is not distorted.
8.4. Inclusion and exclusion. Beware of the voltage of supply network! Supply voltage of the network
must conform to the details shown on the plate of power. Appliances marked with 230 V, can be supplied
with a voltage of 220 V.
8.5. To turn the drill press and hold the trigger switch (1). For locking of the starting switch pressed (1)
press (3). Exclusion relax power trigger switch (1), respectively, if anchored to the button (3), first press
the short term and then release the trigger switch (1).
8.6. Adjust the speed of rotation. Drill allows to work with different speed of spindle. Alignment is done
Publicidad
Tabla de contenido
