Raider industrial RDI-ID38 Manual Del Usuario página 13

using the position (2). In the range of each setting a speed can be adjusted smoothly by increasing speed
and reducing pressure on the trigger button (1). Zavarteneto right speed regulator (2) leads to increase
their rotation and left to decrease.
8.7. Correct choice of the rate of speed shall be held where drill is included without load. So speed-
minded when working with a load may be lower.
8.8. Hammer drilling.
Place the switthe symbol "hammer drilling." Switch falls in the correct position with a distinct twinge.
8.9. Tools to develop or cornering.
Turntable working instrument can be bent. After continuous operation with low-speed power to cool
as to leave it idling for approximately 3 minutes with a maximum speed of rotation. When working with
terminals must always use a universal extension. Use only the cores that are suitable for heads of
screws. Turning to always place the switch "drilling / hammer drilling» in position «Drilling».
8.10. Select the direction of rotation. With the switch you can change the direction of rotation of power.
Rotate right: For drilling and turning the screw press to switch the direction of rotation at point blank
range left. Rotate left: To develop the screws and nuts, press switch direction of rotation right to the point
blank range. Switch he choice of operation should be in position «Drilling». It must be done to change
the direction of rotation when the spindle rotates a drill!
8.11. Not used in rotation to the left mode of attack.
8.12. When you need to vent large diameter, is recommended first to break a small opening, which will
then be drilling to the desired size. This will prevent overloading the drill. Drilling deep holes should be
done gradually, as periodically removed from the drill hole to remove chips or dust. If during drilling to
drill holes in zaklini, you should exclude drill. Use a change of direction of rotation to remove the drill from
the hole. Drill must be kept in alignment with the hole. Ideally, the drill should be placed perpendicular
to the surface of the material being processed. If the condition for perpendicularity is not respected at
work can lead to trapped or breakage in drill hole and injury to the user. Continued drilling at low speed
the engine from overheating threatens. Must make periodic breaks during work or to allow the drill to
work on no-load maximum speed for about 3 minutes. Do not obscure the openings in the hull used for
ventilation of the engine.
8.13. Outdoor use.
Switch the machine only in installations equipped with electric switch "Fi" RCD (Residual Current
Device). RCD must be no more than 30 mA. Use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
Make periodic breaks at work.
Keep and refer to the accessories carefully.
Do not throw the tool, do not overload, do not soak in water and other liquids do not use it for mixing
adhesives and concrete coatings.
9. Service and support.
9.1. Impact drill does not require additional lubrication or special maintenance. There are no parts
requiring maintenance by the user. Never use water or any liquid chemical cleaning drill. It should only
be wiped with a piece of dry tissue. Should always be stored in a dry place and ventilation holes in the
body of the drill to be free.
9.2. Replacing carbon brushes.
Exports (shorter than 5 mm), up or broken engine carbon brushes should be replaced. Always replace
both brushes simultaneously. Work on replacement of carbon brushes entrusted only to qualified person
with original spare parts in service of business RAIDER.
9.3. The repair of your power is best carried out only by qualified specialists in workshops RAIDER,
which used only original spare parts. Thus ensuring their safe operation.
10. Environmental protection.
In view of environmental power, additional accessories and packaging must be subjected
to appropriate processing for reuse of the information contained in these materials.
Do not dispose of household waste power! Under the EU Directive 2012/19/EC on
scrapped electrical and electronic equipment and promoting law and national power,
which can be used more, must be collected separately and be subjected to appropriate
processing for recovery of contained therein scrap.
13