Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Installation Instructions for
Herald Outdoor Wall
Outdoor
G
ENERAL RODUCT NFORMATION
P
These fixtures are intended to be installed utilizing
boxes.
This product is safety listed for wet locations.
Incandescent lamps may be dimmed with a standard incandescent dimmer.
LED
lamps may be dimmed with a
additional information.
This instruction shows a typical installation.
1A
ARM
ARM
SCREW
ANCHOR
JUNCTION BOX
ANCHOR
SCREW
8
3
9
MOUNTING
PLATE
15
Temporarily install the mounting plate to the junction box.
1
Mark the anchor hole locations on the mounting plate and remove the mounting plate.
2
Drill appropriate size holes at the marked locations and install the anchors.
3
Install the curved end of the arm to the fixture loop, then secure the other end of the arm to the top of the fixture base using
4
the arm screw.
Secure the mounting plate to the junction box.
5
Screw the anchor screws into the anchors.
6
Connect the fixture to a suitable ground in accordance with local electrical codes.
7
Connect the white fixture wire to the neutral power line wire with a wire nut.
8
Connect the black fixture wire to the hot power line wire with a wire nut.
9
Mount the fixture base onto the mounting plate and secure it with the fixture screws.
10
Install the candle followers by placing them on top of the candle tubes.
11
Screw the lamp into the socket. Refer to the label on the socket for Max Wattage Information.
12
For Model OL13503 Only: Insert the glass panels into the shade and secure them in place using the panel brackets and screws.
13
Install the shade onto the fixture using the shade screws.
14
15
For wet locations, caulk around the base of the fixture with waterproof construction sealant.
I
:
NEC
compliant junction
LED
dimmer. Consult lamp manufacturer for
FIXTURE
6
FIXTURE
BASE
FIXTURE
SCREW
This product must be installed in accordance with
the applicable installation code by a person familiar
with the construction and operation of the product
and the hazards involved.
Use minimum 90°c supply conductors.
LOOP
PANEL SCREW
AND BRACKET
GLASS PANEL
1
OL13501-OL13502-OL13503
O 13501, OL13502, OL13503
L
CAUTION RISK OF FIRE
-
12
11
13
1.1
FIXTURE
LAMP
CANDLE
FOLLOWER
CANDLE TUBE
SHADE
SHADE
SCREW
Publicidad
Manuales relacionados para Feiss OL13501
Resumen de contenidos para Feiss OL13501
- Página 1 Installation Instructions for OL13501-OL13502-OL13503 Herald Outdoor Wall O 13501, OL13502, OL13503 Outdoor ENERAL RODUCT NFORMATION These fixtures are intended to be installed utilizing compliant junction boxes. CAUTION RISK OF FIRE This product is safety listed for wet locations. This product must be installed in accordance with the applicable installation code by a person familiar Incandescent lamps may be dimmed with a standard incandescent dimmer.
- Página 2 ATTENTION RISQUE INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne. Utiliser les conducteurs d'alimentation supérieure à 90° c. BRAS BOUCLE DE VIS DE LUMINAIRE BRAS...
- Página 3 PRECAUCIÓN RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan. Utilizar conductores de suministro mínimo 90° c. BRAZO BUCLE DE LAMPARA TORNILLO...
- Página 4 SAVE THESE INSTRUCTIONS! 7400 Linder Ave, Skokie, 160077 800.969.3347 www.Feiss.com © 2017 Feiss.All rights reserved.The "Feiss" graphic is a registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company...