Operating Instructions; Preparing The Spray Area; Unit Operation/Setup; Sprayer Operation During Cleaning - CLOROX Total 360 CLX1100 Manual Del Usuario

OPERATING INSTRUCTIONS

Preparing the Spray Area

1. Clean gross filth by using standard manual cleaning protocols.
2. Close the room to the general public for cleaning. Place signs
or warning indicators on doors that indicate no one should
enter the room.
3. Power off any sensitive electrical devices but do not unplug them.

Unit Operation/Setup

1. Choose the appropriate Clorox-approved product for cleaning,
sanitizing or disinfecting.
2. Mount desired Clorox-approved product on Clorox® Total
360® Electrostatic Sprayer base. Ensure that the bottles are
positioned with the opening facing up and the opening facing
the dispensing tubes.
3. Unscrew the lid on the Clorox-approved product of your choice,
remove seal (if present), and connect the Clorox® Total 360®
Electrostatic Sprayer dispensing cap to the bottle. Be sure the
cap is screwed all the way down; do not overtighten.
4. Unwrap electrical cord completely and plug Clorox® Total 360®
Electrostatic Sprayer into a grounded, three-pronged socket.
5. Put on appropriate personal protective equipment. See section
on personal protective equipment on page 5.
6. Locate the On/Off switch on the base unit. Push the Total 360®
sprayer to the "On" position. A blue light will illuminate on both
the sprayer instrument panel and unit power switch.
7. Remove the sprayer from the unit. A blue power indicator light
should be illuminated on the sprayer.
8. The system is now ready for use.
9. Priming the Clorox® Total 360® Electrostatic Sprayer: Depress
into an inconspicuous corner, container or drain. Spray the
Clorox® Total 360® Electrostatic Sprayer for about 20 seconds
to generate a steady flow of solution.
10. When spraying, a second blue indicator light will illuminate on
the sprayer instrument panel when the trigger is depressed.
NOTE: Sprayer will automatically stay on until trigger is
depressed an additional time.
NOTE: Unit will not operate properly below 40°F (4.5°C).

Sprayer Operation During Cleaning

1. Position Clorox® Total 360® Electrostatic Sprayer in a rear
corner of the area.
2. Direct the nozzle at the desired surface.
3. Begin to spray. Press the sprayer button once to initiate
spraying. Press once to stop flow of the sprayer.
4. Follow a continuous path around the area working from high
to low areas, moving the sprayer in a sweeping motion until
surfaces are thoroughly wet.
5. After spraying, keep the area closed to the public,
based on product SDSs.
6. Remove the closed sign from the door once the reentry
time has expired.
8 | EN

Changing Clorox-Approved Products

1. Stop spraying the Clorox® Total 360® Electrostatic Sprayer.
2. Disconnect the bottle connection from the Clorox-approved
product that is to be changed and remove from the sprayer.
Cap the removed product if it is being stored.
3. Purging the Clorox® Total 360® Electrostatic Sprayer: Depress
into an inconspicuous corner, container or drain. Spray the
Clorox® Total 360® Electrostatic Sprayer for about 20 seconds
to purge the system.
4. Choose the appropriate Clorox-approved product for cleaning,
sanitizing or disinfecting.
5. Mount desired Clorox-approved product on Clorox® Total
360® Electrostatic Sprayer base. Ensure that the bottles are
positioned with the opening facing up and the opening facing
the dispensing tubes.
6. Unscrew the lid on the Clorox-approved product of your choice,
remove seal (if present), and connect the Clorox® Total 360®
Electrostatic Sprayer dispensing cap to the bottle. Be sure the
cap is screwed all the way down; do not overtighten.
7. Priming the Clorox® Total 360® Electrostatic Sprayer: Depress
into an inconspicuous corner, container or drain. Spray the
Clorox® Total 360® Electrostatic Sprayer for about 20 seconds
to generate a steady flow of solution.

After Use and Storage

1. Stop spraying the Clorox® Total 360® Electrostatic Sprayer.
2. Disconnect the bottle connection from the Clorox-approved
product that is to be changed and remove from the sprayer.
Cap the removed product if it is being stored.
3. Emptying drip cup holder (if necessary): Rotate the drip cup
90 degrees, making sure to hold it level to prevent spillage.
Remove and empty the drip cup. Reinstall the empty drip
cup by rotating it 90 degrees in the opposite direction until
it is snug.
4. Purging the Clorox® Total 360® Electrostatic Sprayer:
Depress into an inconspicuous corner, container or drain.
Spray the Clorox® Total 360® Electrostatic Sprayer for
about 20 seconds to purge the system.
5. Turn off the unit. Blue indicator light on the instrument panel
and base of the unit should no longer be illuminated.
6. Unplug the Clorox® Total 360® Electrostatic Sprayer from wall.
7. Wrap cord on cord holder on the Clorox® Total 360® base unit.
8. Store in a safe, dry place.