1. Manuales
  2. Marcas
  3. Metra Manuales
  4. Accesorios de Automóviles
  5. 99-6506
  6. Instrucciones de instalación

Metra 99-6506 Instrucciones De Instalación

Ocultar thumbs
1
2
3
4
5
6
7
8

Publicidad

Idiomas disponibles

Idiomas disponibles

Tabla de contenido

KIT COMPONENTS
• A) Radio trim panel • B) ISO radio brackets • C) Trim plate
A
Metra. The World's Best Kits.
®
Chrysler Pacifica 2004-2008
KIT FEATURES
• DIN radio provision with pocket
• ISO DIN radio provision with pocket
B
MetraOnline.com
C
© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION
99-6506
I N S TA L L AT I O N I N S T R U C T I O N S
U.S. Patent # D531,879
TABLE OF CONTENTS
Dash Disassembly . .................................................2
Kit Assembly
–DIN radio provision with pocket ........................3
–ISO DIN radio provision with pocket . .................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: CHTO-02 amplified interface
• 70-6506 amplified bypass harness
Antenna Adapter: 40-CR10
TOOLS REQUIRED
• Phillips screwdriver • Socket wrench
• Small flat blade screwdriver • Cutting tool
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
REV. 5/14/18 INST99-6506

Publicidad

Tabla de contenido
loading

Manuales relacionados para Metra 99-6506

Resumen de contenidos para Metra 99-6506

  • Página 1 Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 5/14/18 INST99-6506...

  • Página 2: Dash Disassembly

    DASH DISASSEMBLY 1. Loosen (1) T-15 Torx screw from the front 4. Unsnap and remove the dash trim side of the shift knob and pull up to panels from each side of the radio/ remove. (Figure A) climate controls. (Figure C) 5. Remove (4) Phillips screws to Note: For models equipped without a release lever on the shift knob, just turn remove the radio. counter-clockwise to remove. Note: When installing a DIN radio, a 2. Unsnap the floor console trim around piece of plastic in the dash cavity may have to be removed for radio clearance the shifter. Unplug the harness to console trim and remove the trim. (Figure D). (Figure B) Continue to Kit Assembly (Figure A) (Figure C) 3. Unsnap and remove the ignition...

  • Página 3: Kit Assembly

    2. Slide the aftermarket radio into the cage 2. Slide the bracket/radio assembly into and secure. Snap the trimplate into the the radio opening until the side clips radio housing. (Figure B) engage. Snap the trim plate into the radio housing. (Figure B) 3. Locate the factory wiring harness and 3. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to antenna connector in the dash and (Figure A) (Figure A) the radio. Metra recommends using the complete all necessary connections to proper mating adapter from Metra. Test the radio. Metra recommends using the the radio for proper operation. proper mating adapter from Metra. Test the radio for proper operation. 4. Secure the completed assembly into the 4. Secure the completed assembly into the dash using the factory screws. dash using the factory screws. 5. Reassemble the dash in reverse order 5. Reassemble the dash in reverse order of disassembly.
  • Página 4 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 5/14/18 INST99-6506...
  • Página 5 Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando. The World’s best kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 5/14/18 INST99-6506B...

  • Página 6: Desmontaje Del Tablero

    DESMONTAJE DEL TABLERO 1. Afloje (1) tornillo T-15 Torx del frente de 4. Suelte a presión y quite los paneles de la la palanca de velocidades y jale hacia moldura del tablero en cada lado de los arriba para retirar. (Figura A) controles de radio/clima.

  • Página 7: Ensamble Del Kit

    Metra recomienda el uso de un necesarias al radio. Metra recomienda el adaptador de acoplamiento apropiado uso de un adaptador de acoplamiento de Metra.
  • Página 8 800-354-6782 for more information and take steps www.installerinstitute.com o llame al toward a better tomorrow. 800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda MECP Técnicos certificados The World’s best kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 5/14/18 INST99-6506B...

Tabla de contenido