Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ENGlIsh
The aggressiveness of the cut increases as the lever is
adjusted from one to three, with three being the most
aggressive cut.
Removable Shoe Sleeve (Fig. D)
The non-marring shoe sleeve
cutting surfaces that scratch easily, such as laminate, veneer,
or paint. It can also be used to protect the shoe surface
during transportation and storage.
To attach shoe sleeve, place the front of the shoe
front of the shoe sleeve and lower the jig saw as shown in
Figure F. The shoe sleeve will click securely onto the rear of
the shoe.
To remove shoe sleeve, grasp the sleeve from the bottom at
the two rear tabs and pull down and away from the shoe.
Hints for Optimum Use
Sawing laminates
•
As the saw blade cuts on the upward stroke, splintering
may occur on the surface closest to the shoe plate.
•
Use a fine-tooth saw blade.
•
Saw from the back surface of the workpiece.
•
To minimize splintering, clamp a piece of scrap wood
or hardboard to both sides of the workpiece and saw
through this sandwich.
Sawing metal
•
Be aware that sawing metal takes much more time than
sawing wood.
•
Use a saw blade suitable for sawing metal.
•
When cutting thin metal, clamp a piece of scrap wood
to the back surface of the workpiece and cut through
this sandwich.
•
Spread a film of oil along the intended line of cut for easier
operation and longer blade life. For cutting aluminum,
kerosene is preferred.
Rip/Circle Cutting (Fig. E, F)
Ripping and circle cutting without a pencil line is easily done
with the rip fence / circle guide (not included; available at
extra cost).
Using the screw supplied with the accessory guide,
position and thread the screw into the shoe to clamp the
fence securely.
When ripping, slide the rip fence under the screw from either
side of the saw. Set the cross bar at desired distance from
blade and tighten screw. For ripping, the cross bar should be
down and against the straight edge of the workpiece.
When circle cutting, adjust rip fence so that distance from
blade to hole in fence arm is at the desired radius and tighten
screw. Place saw so that hole in fence arm is over centre of
circle to be cut (drill hole for blade or cut inward from edge
of material to get blade into position). When saw is properly
positioned, drive a small nail through hole in fence arm.
Using rip fence as a pivot arm, begin cutting circle. For circle
cutting, the cross bar should be up.
16
should be used when
5
6
into the
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear approved eye protection
when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
Repairs
The charger and battery pack are not serviceable.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement) should be performed by a
D
WALT factory service center or a D
e
service center. Always use identical replacement parts.
Protecting the Environment
Separate collection. Products and batteries marked
w
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that
can be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions.
spECIFICaTIoNs
DWE300
aR
B3
Made in:
Brazil
China
Voltage
220 V
120 V
Frequency
50 Hz
60 Hz
Power
Speed
Weight
WALT recommended
e
WALT authorized
e
B2
BR
Brazil/China
Brazil
220 V
127 V
50–60 Hz
60 Hz
650 W
500-3200/min (rpm)
2.4 kg (5.3lbs)
Publicidad
Tabla de contenido
