Ocultar thumbs Ver también para 99-7353CH:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Kia Rio, Rio5 2012-2015
KIT FEATURES
• ISO DIN radio provision with pocket
• Painted Charcoal
KIT COMPONENTS
• A) Radio housing trim panel • B) Radio brackets • C) Pocket • D) Start/Stop switch blank plate
• E) Airbag light blank plate • F) (2) #8 x 3/8" Phillips pan-head screws • G) (5) #8 x 3/8" Phillips truss-head screws
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7304
Antenna Adapter: • Not required
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver • Socket wrench
METRA. The World's best kits.
Installation instructions for part 99-7353CH
99-7353CH
C
D
E
F
G
metraonline.com
Table of Contents
Dash Disassembly ..................................................2
Kit Preparation ........................................................2
Kit Assembly
– ISO DIN radio provision with pocket ....................... 3
CAUTION!
Metra recommends disconnecting the negative bat -
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con -
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Metra 99-7353CH

  • Página 1 • E) Airbag light blank plate • F) (2) #8 x 3/8” Phillips pan-head screws • G) (5) #8 x 3/8” Phillips truss-head screws CAUTION! Metra recommends disconnecting the negative bat - tery terminal before beginning any installation, unless the vehicle manufacturer recommends against so.
  • Página 2: Dash Disassembly

    99-7353CH Dash Disassembly 5. Remove the (8) Phillips screws 1. Unclip and remove the factory radio trim panel including the a/c securing the a/c vents then unclip vents. (Figure A) and remove them from the radio trim panel. (Figure B) Note: Remove the (8) retaining clips to be reused in Kit Assembly.
  • Página 3: Kit Preparation

    Radio Housing Trim Panel. supplied with the radio. (Figure B) (Figure A) 4. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation.
  • Página 4: Important

    Installation instructions for part 99-7353CH IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated.
  • Página 5: Características Del Kit

    Installation instructions for part 99-7353CH Table of Contents Kia Rio, Rio5 2012-2015 99-7353CH Desmontaje del tablero ..........2 Preparación del kit ..........2 Ensamble del kit – Provisión de radio ISO DIN con bolsillo ....3 CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DIN con bolsillo •...
  • Página 6: Desmontaje Del Tablero

    99-7353CH Desmontaje del tablero 1. Desenganche y quite el panel de la 5. Quite los (8) tornillos Phillips moldura del radio de fábrica, incluyendo las que sujetan las rejillas del aire acondicionado y luego desengánchelos rejillas del aire acondicionado. (Figura A) y quítelos del panel de la moldura del...
  • Página 7: Preparación Del Kit

    (Figura A) suministrados con el radio. (Figura 4. Ubique el arnés de cableado de fábrica y el conector de la antena en el tablero. Metra recomienda el uso de adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. 5. Vuelva a armar el tablero al revés Nota: Una placa en blanco de como lo desarmó.
  • Página 8: Importante

    Installation instructions for part 99-7353CH IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones.

Tabla de contenido